Intellijel Metropolix Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 138

Intellijel Metropolix Скачать руководство пользователя страница 9

Once connected, the cabling between the module and power supply should resemble the picture
below:

Before   reconnecting   power   and
turning   on   your   modular   system,
double   check   that   the   ribbon   cable   is
fully   seated   on   both   ends   and   that   all
the   pins   are   correctly   aligned.   If   the
pins   are   misaligned   in   any   direction   or
the   ribbon   is   backwards   you   can
cause   damage   to   your   module,   power
supply,   or   other   modules.

After   you   have   confirmed   all   the
connections,   you   can   reconnect   the
power   cable   and   turn   on   your   modular
system.   You   should   immediately

check that all your modules have powered on and are functioning correctly. If you notice any
anomalies, turn your system off right away and check your cabling again for mistakes.

Connecting an Optional Expander Module

You can connect an

Intellijel Gx

(or

Qx

) gate expander module to Metropolix to provide eight

additional gate and trigger outputs, which you configure via the

on the Metropolix panel.

1.

Turn off power to your eurorack system.

2.

Using   the   power   power   cable   included   with   your   expander   module   (Gx   or   Qx),   connect   one   end
to   the   module’s   10-pin   power   connector   and   the   other   to   the   16-pin   power   socket   on   your
eurorack   system’s   powered   bus   board   —   paying   attention   to   polarity   (aligning   the   red   stripe   as
described   previously).

3.

Using   the   I2C   cable   included   with   your   expander   module,   connect   one   end   to   the   module’s   6-pin
I2C   connector   and   the   other   end   to   the   I2C   port   on   your   Metropolix   module.   Both   ports   are
shrouded   to   ensure   they   can   be   connected   in   only   one   direction.

4.

Power up your eurorack system.

IMPORTANT !!! : Always power down the modules before connecting or disconnecting an
I2C cable.

Metropolix Manual

8

«
...
7
8
9
10
11
...
»

Содержание Metropolix











































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды