Intelligent Weighing Technology QHD+15 Скачать руководство пользователя страница 28

Страница: 28 / 37

- 28 -

2. Replace display board



Remove the top cover



Remove the seven screws from the display board and clean the glue.



Disconnect the key board connecter and main PCB connecter from the display
board.



Remove the display board.



Install a new display board.



Connect the key board connecter and main

PCB connecter.



Turn on the power and check the working condition. Then, turn off the power.



Fix the seven screws and apply glue.



Close the top cover.

3. Replace load cell



Open the top cover.



If necessary remove the PCB’s for avoid damage.



Disconnect load cell connections from the PCB.



Remove the four foots from the bottom cover.



Remove the four screws from the upper bracket.



Remove the bracket

with load cell from

the cover.



Bracket set place on

the table.



Remove the allen

screws from the top

and bottom brackets

by using 5mm allen

key.



Load cell will get

separate from the

bracket.



Install the new load

cell.



Fix the brackets proper.



Fix whole bracket to the bottom cover by using four
screws.



Fix the four foots to the bottom cover.



Connect the load cell connections to the main PCB.



Fix all PCB’s and cables proper.



Close the top cover.

4. Replace battery



Remove the pan and dust cover.



Open the battery cover from the top cover.

Содержание QHD+15






































Результаты поиска

Содержание QHD+15

Отзывы:

Похожие инструкции для QHD+15

Бренды по названию

Популярные бренды

Intelligent Weighing Technology QHD+15, Руководство по обслуживанию

Результаты поиска

Содержание QHD+15

Отзывы:

Похожие инструкции для QHD+15

Бренды по названию

Популярные бренды