background image

v240C – Marine Satellite Communication System

156

 

4

Wi-Fi Access Point 

Configuration

- SSID : The SSID is the network name shared among all

devices in a wireless network. The SSID must be identical

for all devices in the wireless network. It is case-sensitive

and must not exceed 32 alphanumeric characters, which

may be any keyboard character. Make sure this setting is

the same for all devices in your wireless network.

- Channel : Select an appropriate channel from the list

provided to correspond with your network settings. All

devices in your wireless network must use the same

channel in order to function correctly. Try to avoid conflicts

with other wireless networks by choosing a channel where

the upper and lower three channels are not in use.

- Authentication Type : Module supports an authentication

mode that the 802.11 device uses when it authenticates and

associates with an access point or IBSS cell.

- Password : WiFi access password.

- Max Stations : Setting max stations.

 

5

Network Service 

Configuration

- Telnet Service : Enable or disable telnet login support.

- HTTPS Port : HTTPS port number.

 

6

Sys Log

Configuration

Set the system log configuration.

Antenna sends log messages according to emergency level.

Enabling this function sends the message to your management

server.

- Management Server : Sys log function enable/disable

- Server IP : Management server IP address

- UDP Port : Management port

- Message Type : Select message type (Intellian message level)

to send to management server (Lower number indicates higher

emergency).

- Sys log Target Level : If you select this target level,

the management server receives log message equal to or less

than this level.

 

7

Browser

Configuration

Setting refresh rate and refresh disable time.

- Refresh Rate : Set the browser refresh rate

  (Default 1 seconds. Range 1~99).

- Refresh Disable Time : Set the browser idle time-out

  (Default:9 minutes. Range 0~9). To use this function, check the 

  check box.

Содержание v240C


















































































































































































Отзывы: