Intel UPI- 41A Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 69

background image

UPI-41A/41AH/42/42AH USER’S MANUAL

231318 – 20

Figure 2-15. External Reset Configuration

The RESET input performs the following functions:

#

Disables Interrupts

#

Clears Program Counter to Zero

#

Clears Stack Pointer

#

Clears Status Register and Flags

#

Clears Timer and Timer Flag

#

Stops Timer

#

Selects Register Bank 0

#

Sets PORTS 1 and 2 to Input Mode

DATA BUS BUFFER

Two 8-bit data bus buffer registers, DBBIN and
DBBOUT, serve as temporary buffers for commands
and data flowing between it and the master processor.
Externally, data is transmitted or received by the DBB
registers upon execution of an INput or OUTput in-
struction by the master processor. Four control signals
are used:

#

A

0

Address input signifying control or data

#

CS

Chip Select

#

RD Read Strobe

#

WR Write Strobe

Transfer can be implemented with or without UPI pro-
gram interference by enabling or disabling an internal
UPI interrupt. Internally, data transfer between the
DBB and the UPI accumulator is under software con-

trol and is completely asynchronous to the external
processor timing. This allows the UPI software to han-
dle peripheral control tasks independent of the main
processor while still maintaining a data interface with
the master system.

Configuration

Figure 2-16 illustrates the internal configuration of the
DBB registers. Data is stored in two 8-bit buffer regis-
ters, DBBIN and DBBOUT. DBBIN and DBBOUT
may be accessed by the external processor using the
WR line and the RD line, respectively. The data bus is
a bidirectional, three-state bus which can be connected
directly to an 8-bit microprocessor system. Four con-
trol lines (WR, RD, CS, A

0

) are used by the external

processor to transfer data to and from the DBBIN and
DBBOUT registers.

An 8-bit register containing status flags is used to indi-
cate the status of the DBB registers. The eight status
flags are defined as follows:

#

OBF Output Buffer Full

This flag is automatically set when the UPI-Micro-
computer loads the DBBOUT register and is cleared
when the master processor reads the data register.

#

IBF Input Buffer Full

This flag is set when the master processor writes a
character to the DBBIN register and is cleared
when the UPI INputs the data register contents to
its accumulator.

20

«
...
22
23
24
25
26
...
»

Содержание UPI- 41A






































































Отзывы:

Нет отзывов

Похожие инструкции для UPI- 41A

Бренд: Paradyne Страницы: 22

Enterprise Filter Authentication R3000

Бренд: 8e6 Technologies Страницы: 66

neutrino series

Бренд: Xilica Audio Design Страницы: 26

S5120V3-EI Series

Бренд: H3C Страницы: 54

Бренд: Ublox Страницы: 116

Бренд: Acqiris Страницы: 22

Бренд: Digitus Страницы: 8

Бренд: Genie Страницы: 15

Бренд: ZALMAN Страницы: 9

Бренд: Endace Страницы: 51

Бренд: Supero Страницы: 16

iCE40 SPRAM Series

Бренд: Lattice Semiconductor Страницы: 12

Бренд: Patton electronics Страницы: 145

ipRocketLink IAD 3086

Бренд: Patton electronics Страницы: 12

Бренд: OPTO 22 Страницы: 28

IQ Switch ProxSense RS100

Бренд: Azoteq Страницы: 9

Бренд: Citizen Страницы: 50

Facility Explorer

Бренд: Johnson Controls Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды