Intel SRCS14L - RAID Controller Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 31

background image

Hardware Installation and User’s Guide

13

Hardware Installation

Hardware Installation

2

This chapter provides information on installing the IIR controller, programming the Flash
memory, setting jumpers, and using the LEDs and alarms to diagnose the controller.

2.1

Installation Procedures

Warning:

Shock hazards may be present inside the computer in which this controller is being
installed. Disconnect all power cords to the computer before the removal of any
covers.

Follow the warnings noted in your computer’s user manual before installing this board.
ONLY after reinstallation of all the covers should you reconnect the power cords and
power up the computer.

Note:

Take precautions to prevent electrostatic discharge (ESD) damage before handling the IIR
controller.

2.1.1

Computer System Hardware Requirements

•

Computer with CD-ROM drive

•

One available 64-bit/66MHz PCI slot for optimal performance; however, the controller
is backwards compatible with all 33MHz PCI expansion slots.

•

PCI 2.2 compliant system BIOS

«
...
11
12
13
14
15
...
»

Содержание SRCS14L - RAID Controller
































Отзывы:

Нет отзывов

Похожие инструкции для SRCS14L - RAID Controller

Бренд: EAW Страницы: 6

Бренд: EAW Страницы: 6

Бренд: YASKAWA Страницы: 34

Бренд: Yamaha Страницы: 24

Бренд: Yamaha Страницы: 5

Бренд: STONEFLY Страницы: 48

Бренд: ForeScout Страницы: 28

Бренд: TANDBERG Страницы: 3

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Бренд: Intel Страницы: 86

Бренд: Arbor Technology Страницы: 8

Бренд: Idis Страницы: 17

Бренд: Atmel Страницы: 2

Бренд: Acromag Страницы: 23

Бренд: Top Страницы: 21

Accelero TWIN TURBO II

Бренд: Arctic Страницы: 2

Бренд: Alcatel-Lucent Страницы: 12

Бренд: LevelOne Страницы: 4

Vortex86SX VSX-6101

Бренд: ICOP Technology Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды