background image

 x

Intel® Server Compute Blade SBX44:  Installation and User’s Guide 

 

Electromagnetic compatibility notices (International)

Europe (CE Declaration of Conformity): This product has been tested in accordance to, and 
complies with the Low Voltage Directive (73/23/EEC) and EMC Directive (89/336/EEC). The 
product has been marked with the CE Mark to illustrate its compliance.

Japan EMC Compatibility:

English translation of the notice above: This is a Class A product based on the standard of the 
Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this 
equipment is used in a domestic environment, radio disturbance may arise. When such trouble 
occurs, the user may be required to take corrective actions.

ICES-003 (Canada): Cet appareil numérique respecte les limites bruits radioélectriques applicables 
aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur: "Appareils 
Numériques", NBM-003 édictée par le Ministre Canadian des Communications.

English translation of the notice above: This digital apparatus does not exceed the Class A limits 
for radio noise emissions from digital apparatus set out in the interference-causing equipment 
standard entitled "Digital Apparatus", ICES-003 of the Canadian Department of Communications.

BSMI (Taiwan): The BSMI Certification number and the following warning is located on the 
product safety label which is located visibly on the external chassis.

Содержание SBX44 - Server Compute Blade





























































































Отзывы: