Intel PCH-LP Скачать руководство пользователя страница 77

Страница: 77 / 90

523462

Intel Confidential

APPENDIX A - Descriptor Configuration

A.4

PCHSTRP2—Strap 2 Record (Flash Descriptor

Records)

Flash Address:

FPSBA + 008h

Size: 32 bits

Default Flash Address: 108h

Bits

Description

Usage

31:25

Intel

ME SMBus I

C* Address (MESMI2CA):

Defines 7 bit Intel ME SMBus I

C target address

Note:

This field is only used for testing purposes

This address is only used by Intel ME FW for testing

purposes. If MESMI2CEN (PCHSTRP2 bit 24) is set

to 1 then the address used in this field must be non-

zero and not conflict with any other devices on the

segment.

Intel

ME SMBus I

C Address Enable (MESMI2CEN):

0 = Intel ME SMBus I

C Address is disabled

1 = Intel ME SMBus I

C Address is enabled

Note:

This field is only used for testing purposes on Intel

ME FW

This field should only be set to ’1’ for testing purposes

23:17

Intel

ME SMBus MCTP Address (MESMMCTPA):

Defines 7 bit Intel ME SMBus MCTP target address

Note:

This field is only used for testing purposes on Intel

ME FW.

This address is used by Intel ME Anti-Theft

Technology.

If MESMMCTPAEN (PCHSTRP2 bit 16) is set to 1

then the address used in this field must be non-zero

and not conflict with any other devices on the

segment.

Intel

ME SMBus MCTP Address Enable

(MESMMCTPAEN):
0 = Intel ME SMBus MCTP Address is disabled

1 = Intel ME SMBus MCTP Address is enabled

Note:

This field is only used for testing purposes on Intel

ME FW

This field should only be set to ’1’ for testing purposes

on platforms that use Intel ME FW.

15:9

Intel

ME SMBus Alert Sending Device (ASD) Address

(MESMASDA):
Intel ME SMBus Controller ASD Target Address.

Note:

This field is only applicable if there is an ASD

attached to SMBus and using Intel

AMT

If MESMASDEN(PCHSTRP2 bit 8) is set to ’1’ there

must be a valid address for ASD. The address must be

determined by the BIOS developer based on the

requirements below.

A valid address must be:

• Non-zero value
• Must be a unique address on the Host SMBus

segment

• Be compatible with the master on SMBus - For

example, if the ASD address the master that

needs write thermal information to an address

"xy"h. Then this field must be set to "xy"h.

Intel

ME SMBus Alert Sending Device (ASD) Address

Enable (MESMASDEN):
0 = Intel ME SMBus ASD Address is disabled

1 = Intel ME SMBus ASD Address is enabled

Note:

This field is only applicable if there is an ASD

attached to SMBus and using Intel AMT

This bit must only be set to ’1’ when there is an ASD

(Alert Sending Device) attached to Host SMBus. This

is only applicable in platforms using Intel AMT.

Note:

This setting is not the same for all designs, is

dependent on the board design. The setting

of this field must be determined by the BIOS

developer and the platform hardware

designer.

7:0

Reserved, set to ’0’

Содержание PCH-LP



























































































Результаты поиска

Содержание PCH-LP

Отзывы:

Похожие инструкции для PCH-LP

Бренды по названию

Популярные бренды

Intel PCH-LP, Руководство по программированию

Результаты поиска

Содержание PCH-LP

Отзывы:

Похожие инструкции для PCH-LP

Бренды по названию

Популярные бренды