Electrical Specifications
62
Datasheet, Volume 1
9.
The processor should not be subjected to any static V
TTA,
V
TTD
level that exceeds the V
TT_MAX
associated
with any particular current. Failure to adhere to this specification can shorten processor lifetime.
10. Baseboard bandwidth is limited to 20 MHz.
11. DC + AC + Ripple specification.
12. The loadlines specify voltage limits at the die measured at the VCC_SENSE and VSS_SENSE lands. Voltage
regulation feedback for voltage regulator circuits must also be taken from processor VCC_SENSE and
VSS_SENSE lands.
13. V
SA_VID
does not have a loadline, the output voltage is expected to be the VID value.
14. V
CCD
tolerance at processor pins. Tolerance for VR at remote sense is ±3.3%*V
CCD
.
15. The V
CCPLL
, V
CCD01
, V
CCD23
voltage specification requirements are measured across vias on the platform.
Choose V
CCPLL
, V
CCD01
, or V
CCD23
vias close to the socket and measure with a DC to 100 MHz bandwidth
oscilloscope limit (or DC to 20 MHz for older model oscilloscopes), using 1.5 pF maximum probe
capacitance, and 1 M
Ω
minimum impedance. The maximum length of the ground wire on the probe should
be less than 5 mm to ensure external noise from the system is not coupled in the scope probe.
16. DC + AC + Ground Noise specification.
17. VCC has a Vboot setting of 0.0 V and is not included in the PWRGOOD indication.
18. VSA has a Vboot setting of 0.9 V.
Notes:
1.
Unless otherwise noted, all specifications in this table apply to all processors. These specifications are
based on pre-silicon characterization and will be updated as further data becomes available.
2.
I
CC_TDC
(Thermal Design Current) is the sustained (DC equivalent) current that the processor is capable of
drawing indefinitely and should be used for the voltage regulator thermal assessment. The voltage
regulator is responsible for monitoring its temperature and asserting the necessary signal to inform the
processor of a thermal excursion.
3.
Specification is at T
CASE
= 50 °C.
Characterized by design (not tested).
4.
I
CCD_01_MAX
and I
CCD_23_MAX
refers only to the processor’s current draw and does not account for the
current consumption by the memory devices.
5.
Minimum V
CC
and maximum I
CC
are specified at the maximum processor temperature. Refer to the
processor Thermal Mechanical Specification and Design Guide (see
Section 1.7, “Related Documents”
for
thermal specifications. ICC_MAX is specified at the relative V
CC_MAX
point on the V
CC
load line. The
processor is capable of drawing I
CC_MAX
for up to 10 ms.
Table 7-10. Current (Icc_Max and Icc_TDC) Specification
Symbol
Parameter
Voltage Plane
4-Core
Max
6-Core
Max
Unit
Notes
1
I
CC_MAX
I
CC_MAX
I
TT_MAX
I
SA_MAX
I
CCD_01_MAX
I
CCD_23_MAX
I
CCPLL_MAX
Max. Processor Current:
(TDP - 130W)
V
CC
V
TTA
/V
TTD
V
SA
V
CCD_01
V
CCD_23
V
CCPLL
150
24
24
4
4
2
165
24
24
4
4
2
A
A
A
A
A
A
4, 5
I
CC_TDC
I
CC_TDC
I
TT_TDC
I
SA_TDC
I
CCD_01_TDC
I
CCD_23_TDC
I
CCPLL_TDC
Thermal Design Current:
(TDP - 130 W)
V
CC
V
TTA
/V
TTD
V
SA
V
CCD_01
V
CCD_23
V
CCPLL
115
20
20
3
3
2
135
20
20
3
3
2
A
A
A
A
A
A
2, 5
I
CCD_S3
DDR3 System Memory
Interface Supply Current in
Standby State
V
CCD_01
V
CCD_23
TBD
TBD
A
3, 4
Содержание BX80619I73960X
