Integral Audio MCSS630-RAM Скачать руководство пользователя страница 23

nO

tes

23

nO

tes

•  AMPLIFIER TURN-ON:  You will notice that the amplifier turns on before the head unit, and remains on 

after the head unit is off.  This is normal.  The sound output system needs to be energized to play your 
door chimes, parking distance control sounds, bluetooth, etc.  The amp will turn on from the moment 
the doors are unlocked or opened, and remain on from between 30 seconds and as much as 20 minutes 
after the car is locked.  Again, this is perfectly normal.  The idle current on the ARC amp is virtually 
zero and will not cause any issues with battery drain. 

•  SIGNAL SOURCE QUALITY:  A poor quality signal will always sound poor no matter how good an audio 

system is.  If you are using MP3s or home-burned CDs it is critical that you understand the limitations 
and impacts of digital compression methods.  MP3s at less than 256kbps will have noticeable loss of 
quality.  Satellite radio is also compressed and will have similar quality issues.  Non-commercially 
obtained music (especially downloaded via P2P file-sharing) recordings are often re-mixed by third par-
ties and will have been compressed in an unknown and uncontrolled manner.  If you want good quality 
sound, use only commercial CDs or MP3s compressed at 256kbps or 320kbps.  

•  FACTORY RADIO SETTINGS:  Please note that the settings (Bass, Treble, Fade, Balance, AUX input level, 

etc.) are stored on the Key FOB & are specific to the Source (Radio, CD, AUX).  You will need to edit and 
save the settings for each source and each FOB  to have consistent sound.

•  PLEASE LISTEN RESPONSIBLY:  Your new Integral Audio system is capable of delivering Sound Pressure 

Levels that can damage your hearing.  It also delivers very clean, low-distortion sound reproduction.  
Because distortion sounds bad to your ears, and low-distortion sounds good, you are much more likely 
to listen at high levels with your new system.  Please exercise caution - we want you to enjoy a lifetime 
of great sound!

having trouble?  the best thing to do is contact us at support@integralaudio.

com or via the phone number listed on the receipt that was emailed to you.  

we’ll get you fixed up aSap!

tr

Ou

Blesh

OO

ting

Содержание MCSS630-RAM
























Отзывы: