IC BLOCK DIAGRAMS AND TERMINAL DESCRIPTIONS -74
Q103 : F2628E-01 (XM Digital Transceiver)
TERMINAL DESCRIPTION(1/2)
DTR-7.8
Pin No.
Pin Name
Direction
Function in Slave Mode
Function in Master Mode
Notes
1
LSDP
S=In
M=Out
Low Speed Data Port Input
Low Speed Data Port Output
Out= 4mA, SLC
In=LVTTL S/T
3
SC_TX_OUT
S=Out
M=Out
System Controller Bus (CBM)
Transmit Data Out
System Controller Bus (CBM)
Transmit Data Out
4mA, SLC
5
SC_RX_IN
S=In
M=In
System Controller Bus (CBM)
Receive Data In
System Controller Bus (CBM)
Receive Data In
LVTTL S/T
6
RFU (I2C-SCL)
S=In
M=In
Reserved for Future Use (pull
down with a 100k resistor to
Ground)
Reserved for Future Use (pull
down with a 100k resistor to
Ground)
LVTTL S/T
7
RFU (I2C-SDA)
S=In
M=In
Reserved for Future Use (pull
down with a 100k resistor to
Ground)
Reserved for Future Use (pull
down with a 100k resistor to
Ground)
LVTTL S/T
9
ANT_REV
S=n/u
M=Out
Not used in Slave mode, leave
unconnected
Indication of incompatible
antenna ( refer to section
4.3.2 for usage)
4mA, SLC
11
RESET#
S=In
M=In
Asynchronous Reset In,
(Active Low)
Asynchronous Reset In,
(Active Low)
LVTTL S/T
12
SLAVE_SEL
S=In
M=In
Master/Slave Mode Select In
(High = Slave Mode)
Master/Slave Mode Select In
(Low = Master Mode)
LVTTL S/T
13
I2S_RATE
S=Out
M=Out
Output driven high, leave
unconnected
Indicator of incoming I2S data
rate (see section 4.4.2)
4mA, SLC
14
LINKACTIVE
S=Out
M=Out
Link Active indicator (High =
DT bus link is active and data
is flowing)
Link Active indicator (High =
DT bus link is active and data
is flowing)
4mA, SLC
15
COMM_TX_EN
S=Out
M=Out
DT Comm Bus External
Transceiver Direction
Control Output (0=Tx, 1=Rx)
DT Comm Bus External
Transceiver Direction
Control Output (0=Tx, 1=Rx)
4mA, SLC
18
COMM_RX_P
S=In
M=In
DT Differential Comm Bus
Internal Receiver Positive In
DT Differential Comm Bus
Internal Receiver Positive In
LVDS in+
19
COMM_RX_M
S=In
M=In
DT Differential Comm Bus
Internal Receiver Negative In
DT Differential Comm Bus
Internal Receiver Negative In
LVDS in–
22
COMM_TX_M
S=Out
M=Out
DT Differential Comm Bus
Internal Transmitter Negative
Out
DT Differential Comm Bus
Internal Transmitter Negative
Out
LVDS out–
23
COMM_TX_P
S=Out
M=Out
DT Differential Comm Bus
Internal Transmitter Positive
Out
DT Differential Comm Bus
Internal Transmitter Positive
Out
LVDS out+
26
OSC_OUT
S=Out
M=Out
Crystal Driver Output
Crystal Driver Output
28
OSC_IN
S=In
M=In
Crystal/ Ext. Clock Input
Crystal/ Ext. Clock Input
29
SC_RATE
(Rev 4A only, pull
down for rev 3B)
S=Out
M=In
SC interface baud rate Output
(High = DT4_MODE is high
and the Master DTIC is
operating at 115.2K baud)
SC interface baud rate select
Input
(High = 115.2K baud, Low =
9600 baud)
Out= 4mA, SLC
In=LVTTL S/T
30
TEST
S=In
M=In
Factory Test Mode Select
(1=Test, 0= Normal Oper.)
Factory Test Mode Select
(1=Test, 0= Normal Oper.)
LVTTL S/T