Integra DTR-50.3, Инструкция по эксплуатации

Страница: 75 / 100

75
En
Integra/Onkyo components that are connected via u are
controlled by pointing the remote controller at the AV
receiver, not the component. This allows you to control
components that are out of view, in a rack, for example.
Controlling Integra/Onkyo components without
u
If you want to control an Integra/Onkyo component by
pointing the remote controller directly at it, or you want to
control an Integra/Onkyo component that’s not connected
via
u , use the following remote control codes:
`
30627 :
Integra/Onkyo DVD player without
u
`
71817 :
Integra/Onkyo CD player without u
`
32900/33100/33500 :
Integra/Onkyo Blu-ray Disc player
`
32901/33104/33504 :
Integra/Onkyo HD DVD player
`
70868 :
Onkyo MD recorder without
u
`
71323 :
Onkyo CD recorder without
u
`
82990 :
Onkyo Dock without u
You can reset a Remote Mode to its default remote
control code.
You can reset the remote controller to its default settings.
By pressing the Remote Mode that’s been programmed
with the remote control code for your component, you can
control your component as described below.
For details on entering a remote control code for other
components, see “Entering Remote Control Codes”
(
➔
page 74 ).
Controlling a TV
TV is preprogrammed with the remote control code for
controlling a TV that supports the
p
*1
(limited to
some models). The TV must be able to receive remote
control commands via
p
and be connected to the
AV receiver via HDMI. If controlling your TV via
p
doesn’t work very well, program your TV’s
remote control code into
TV
and use the TV remote mode
to control your TV.
Use the following remote control codes:
`
11807/13100/13500 :
TV with
p
Controlling a Blu-ray Disc/DVD Player, HD
DVD Player or DVD Recorder
BD/DVD is preprogrammed with the remote control code
for controlling a component that supports the
p
*1
(limited to some models). The component must be able to
receive remote control commands via
p
and be
connected to the AV receiver via HDMI.
Use the following remote control codes:
`
32910/33101/33501/31612 :
Blu-ray Disc/DVD player with p
*1 The p supported by the AV receiver is the CEC
system control function of the HDMI standard.
Remote Control Codes for Integra/Onkyo
Components Connected via
u
1
Make sure the Integra/Onkyo component is
connected with an
u
cable and an analog audio
cable (RCA).
See “Connecting Integra/Onkyo
u
Components”
for details (
➔
page 20
).
2
Enter the appropriate remote control code for
Remote Mode , referring to the previous section.
`
42157 :
Onkyo cassette tape deck with
u
`
81993 :
Onkyo Dock with u
3
Press Remote Mode , point the remote controller
at the AV receiver, and operate the component.
Resetting Remote Mode Buttons
1
While holding down Remote Mode that you want
to reset, press and hold down Home until Remote
Mode button lights (about 3 seconds).
2 Within 30 seconds, press Remote Mode again.
Remote Mode button flashes twice, indicating that
the button has been reset.
Each of
Remote Mode
is preprogrammed with a
remote control code. When a button is reset, its
preprogrammed code is restored.
Note
• The learning command is also reset.
Resetting the Remote Controller
1
While holding down Receiver , press and hold
down Home until Receiver lights (about 3
seconds).
2
Within 30 seconds, press
Receiver
again.
Receiver flashes twice, indicating that the remote
controller has been reset.
Controlling Other Components