Integra DTR-50.3, Инструкция по эксплуатации

Страница: 45 / 100

45
En
■
Resolution
`
Through
*1
:
Select this to pass video through the AV receiver at
the same resolution and with no conversion.
`
Auto
*2
:
Select this to have the AV receiver automatically
convert video at resolutions supported by your TV.
`
480p ( 480p/576p ), 720p , 1080i , 1080p
*2
:
Select the desired output resolution.
`
1080p/24
*2
:
Select this for 1080p output at 24 frames per second.
`
4K Upscaling *2 :
Select this for an output resolution four times that of
1080p, resulting in 3840 × 2160 pixels.
`
Source :
Output will be according to the resolution level
which was set in the “
Picture Adjust ” setting
(
➔
page 55 ).
You can specify the output resolution for the HDMI
Output(s) and
COMPONENT VIDEO MONITOR OUT
and have the AV receiver upconvert the picture resolution
as necessary to match the resolution supported by your
TV.
Tip
• The “ Resolution ” setting is set respectively of main, sub, and
analog.
• You can see the picture by pressing Enter to check the
“ Resolution ” setting (excluding NET input source).
Note
• Depending on the incoming video signal, the video playback
may not be smooth or the vertical resolution may be lowered. In
this case select anything other than “
1080p/24 ”.
• If the “ Monitor Out ” setting is set to “ Both ”, this setting is fixed
to “ Auto ”.
• When “ Monitor Out ” is set to either “ HDMI Sub ” or
“ Both(Sub) ”, “ 1080/24p ” and “ 4K Upscaling ” cannot be
selected.
*1 PC IN (Analog RGB) input signal is output at 480p
(480p/576p), 720p, 1080i resolution when the “
Monitor Out ”
setting is set to “ Analog ” (
➔
page 44
) and the “ Resolution ”
setting is set to “ Through ”.
*2
These settings are not available when the “ Monitor Out ”
setting is set to “ Analog ” (
➔
page 44 ).
HDMI Input
If you connect a video component to an HDMI input, you
must assign that input to an input selector. For example, if
you connect your Blu-ray Disc/DVD player to
HDMI
IN 2 , you must assign “ HDMI2 ” to the “ BD/DVD ” input
selector.
If you’ve connected your TV to the AV receiver with an
HDMI cable, composite video, S-video and component
video sources can be upconverted
*
and output by the
HDMI output
*1
. You can set this for each input selector by
selecting the “ - - - - - ” option. See “Video Connection
Formats” for more information on video signal flow and
upconversion (
➔
page 88
).
*1
This applies only when “ Monitor Out ” setting is set to other
than “ Analog ” (
➔
page 44 ).
Here are the default assignments.
■
BD/DVD , VCR/DVR , CBL/SAT , GAME , PC ,
TV/CD , PHONO , PORT
`
HDMI1 , HDMI2 , HDMI3 , HDMI4 , HDMI5 ,
HDMI6 , HDMI7 :
Select a corresponding HDMI input to which the
video component has been connected.
`
- - - - - :
Output composite video, S-Video, and component
video sources from the HDMI output. The video
output signal from the HDMI output is the one
configured in “Component Video Input”.
*2
If you connect your personal computer to
PC IN
(Analog
RGB), you must assign “ - - - - - ” to the “ PC ” input selector.
Each HDMI input cannot be assigned to two input
selectors or more. When
HDMI1 - HDMI7 have already
been assigned, you must first set any unused input
selectors to “
- - - - - ” or you will be unable to assign
HDMI1 - HDMI7 to other input selectors.
Input selector Default assignment
BD/DVD HDMI1
VCR/DVR HDMI2
CBL/SAT HDMI3
GAME HDMI4
PC
HDMI5
*2
AUX FRONT (Fixed)
TV/CD - - - - -
PHONO - - - - -
PORT - - - - -
IN
OUT
Composite video, S-Video,
component video
HDMI
HDMI
Composite video, S-Video,
component video