Integra DTR-50.3, Инструкция по эксплуатации

Страница: 68 / 100

68
En
Adjusting the Volume for Zones
■
Operating on the remote controller
■
Operating on the AV receiver
If your Zone 2/3 speakers are connected to a receiver or
integrated amp in Zone 2/3, use its volume control to
adjust the volume.
Muting Zones
■
Operating on the remote controller
Tip
• To unmute, press
Zone
followed by
Muting
again. Zones can
also be unmuted by adjusting the volume.
Adjusting the Tone and Balance of Zone 2
Note
• Only analog input sources are output by the ZONE 2/3
PRE/LINE OUT and FRONT WIDE/ZONE 2 L/R terminals.
Digital input sources are not output. If no sound is heard when
an input source is selected, verify that the source is connected to
an analog input.
• While Zone 2/3 is on,
u
functions will not work.
• You cannot select different AM or FM radio stations for your
main room and Zone 2/3. The same AM/FM radio station will be
heard in each room. Namely, if you have selected an FM station
for the main room, that station will also be output in Zone 2/3.
• When you have selected NET or USB as the input selector, the
last selector selected will be set for Main room, Zone 2, and
Zone 3.
• When Zone 2/3 is activated and its input selector is selected, the
power consumption of standby mode slightly increases.
• When setting the AV receiver to standby mode while Zone 2/3
is active, the Z2/3 indicator is dimly lit.
• The Zone 2 volume, tone, and balance function have no effect on
ZONE 2 PRE/LINE OUT when the “ Zone2 Out ” setting is set
to “ Fixed ” (
➔
page 59 ).
• The Zone 3 volume function has no effect on
ZONE 3
PRE/LINE OUT when the “ Zone3 Out ” setting is set to
“ Fixed ” (
➔
page 59 ).
• Even if you repeatedly press the remote controller’s
Zone
to
select zones, the last zone selection will be retained once you
have switched to other components by pressing other
Remote
Mode after pressing Zone .
The 12V triggers A, B, and C can be used to turn on 12V
trigger-capable components automatically when they are
selected as the input source. The triggers can be set so that
they activate when a connected component is selected as
the input source for the main room, Zone 2, Zone 3 or any
combination of rooms. When triggered, the output from a
12V TRIGGER OUT goes high (+12 volts and 150
milliamperes max. at
12V TRIGGER OUT A
; +12 volts
and 25 milliamperes max. at 12V TRIGGER OUT B and
C ).
• See also “12V Trigger A/B/C Setup” (
➔
page 59 ).
Hookup
• Use a miniplug cable to connect the AV receiver’s 12V
TRIGGER OUT A , B , or C jack to the 12 V trigger
input on a connected component.
When several components are turned on simultaneously
by using triggers A, B, and C, depending on the type of
components, a large amount of current may be drawn
momentarily. To prevent this, you can delay trigger
signals A, B, and C individually. Another application of
trigger delay is eliminating the “thump” noise that’s
sometimes heard when a source component is turned on.
You can accomplish this by delaying the trigger signal for
your power amplifier, so that it’s the last component to be
turned on.
1 press Zone repeatedly.
2
Use VOL
q
/
w
to adjust the volume.
1
Press Zone 2 or Zone 3 (the Z2/3 indicator on the
display flash).
2
Use Zone Level q / w within 8 seconds to adjust the
volume.
1
Press Zone repeatedly, and then press Muting .
1
On the AV receiver, press Zone 2 .
2
Press the AV receiver’s Tone repeatedly to select
“Bass”, “Treble” or “Balance”.
3
Use
–/+
to adjust the bass, treble or balance.
• You can boost or cut the bass or treble from –10 dB
to +10 dB in 2 dB steps.
• You can adjust the balance from 0 in the center to
+10 dB to the right or +10 dB to the left in 2 dB
steps.
Using the 12V Triggers