Integra DHC-80.2, Инструкция по эксплуатации

Страница: 65 / 116

65
En
■
Maximum Volume
`
Off , 50 to 99 (Absolute display)
`
Off , –32dB to +17dB (Relative display)
With this setting, you can limit the maximum volume.
To disable this setting, select “
Off ”.
■
Power On Volume
`
Last , Min , 1 to 99 or Max (Absolute display)
`
Last , –
Q
dB , –81dB to +18dB (Relative display)
With this preference, you can specify the volume set-
ting to be used each time the AV controller is turned
on.
To use the same volume level that was used when the AV
controller was turned off, select “
Last ”.
The “ Power On Volume ” cannot be set higher than the
“ Maximum Volume ” setting.
■
Headphone Level
`
–12dB to 0dB to +12dB
With this preference, you can specify the headphone vol-
ume relative to the main volume. This is useful if there’s a
volume difference between your speakers and your head-
phones.
OSD Setup
■
On Screen Display
This preference determines whether operation details
are displayed on-screen when an AV controller function
is adjusted.
`
On :
Displayed.
`
Off :
Not displayed.
Even when “ On ” is selected, operation details may not be
output if the input source is connected to an
HDMI IN
.
■
TV Format (Australian models)
For the on-screen setup menus to display properly, you
must specify the TV system used in your area.
`
Auto :
Select this to automatically detect the TV system
from the video input signals.
`
NTSC :
Select this if the TV system in your area is NTSC.
`
PAL :
Select this if the TV system in your area is PAL.
■
Language
`
English , Deutsch, Français, Español, Italiano,
Nederlands, Svenska, 中文
This setting determines the language used for the
on-screen setup menus.
12V Trigger A/B/C Setup
See “Using the 12V Triggers” (
➔
85 ).
Main menu Hardware Setup
Remote ID
■
Remote ID
`
1 , 2 , or 3
When several Integra/Onkyo components are used in
the same room, their remote ID codes may overlap. To
differentiate the AV controller from the other compo-
nents, you can change its remote ID from “
1 ”, to “ 2 ” or
“ 3 ”.
Note
• If you do change the AV controller’s remote ID, be sure to
change the remote controller to the same ID (see below), other-
wise, you won’t be able to control it with the remote controller.
Changing the Remote Controller’s ID
Multi Zone
See “Setting the Multi Zone” (
➔
82
).
Tuner
For FM/AM tuning to work properly, you must specify the
FM/AM frequency step used in your area. Note that when
this setting is changed, all radio presets will be deleted.
■
FM/AM Frequency Step (North American
models)
`
200kHz/10kHz :
Select if 200 kHz/10 kHz steps are used in your area.
`
50kHz/9kHz :
Select if 50 kHz/9 kHz steps are used in your area.
■
AM Frequency Step (Australian models)
`
10kHz :
Select if 10 kHz steps are used in your area.
`
9kHz :
Select if 9 kHz steps are used in your area.
SIRIUS Settings (North American models)
See “Listening to SIRIUS Satellite Radio
®
” (
➔
33
) for
more information.
Hardware Setup
1
While holding down Receiver , press and hold
down Setup until Receiver lights (about 3 sec-
onds).
2
Use the number buttons to enter ID 1, 2, or 3.
Receiver flashes twice.