INOXPA M-226 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 38

INOXPA M-226 Скачать руководство пользователя страница 18

8.8.3. Assembly of the housing and impeller for the M-226 blender

1.

Slide the impeller (02) over the shaft (05) until it touches the rotating part of the mechanical seal

(08).

2.

Assemble the O-ring (80D) in the slot of the impeller screw (25) and tighten this screw over the

impeller (02) using a box spanner and with a spanner in the motor fan shaft taking care not to

damage it, to avoid the rotation shaft.

3.

Mount the housing (01) and fix it to the lantern (04) using the retention ring (15).

4.

Mount the distribution assembly (102), the internal venturi (103) with its O-ring (80), the butterfly

valve (96) and the hooper (101) with their respective clamps (91,91A) and clamp gaskets (91B,91C).

8.8.4. Assembly of the housing and impeller for the M-440 blender

1.

Slide the impeller (02) over the shaft (05) until it touches the rotating part of the mechanical seal

(08).

2.

Assemble the O-ring (80D) in the slot of the impeller screw (25) and tighten this screw over the

impeller using a box spanner and with a spanner in the motor fan shaft taking care not to damage

it, to avoid the rotation shaft.

3.

Place the protector (47A) and fix it with the screws (50A).

4.

Place the housing (01) and fix it to the lantern (04) using the retention ring (15).

5.

Mount the distribution assembly (102), the internal venturi (103) with its O-ring (80), the butter

-

fly valve (96) and the hooper (101) with their respective clamps (91,91A) and clamp gaskets

(91B,91C).

ATTENTION

Take care to mount the distribution assembly in the correct direction for the blender

correct operation.

8.8.2. Disassembly of the housing and impeller for the M-440 blender

1. Close the suction and the discharge valve.

2. Remove, sequentially, the pieces which are on

the housing (01) top: hooper (101), butterfly val

-

ve (96), distribution assembly (102) and internal

venturi (103), removing the clamps (91,91A) which

join these pieces.

3.

Remove the retention ring (15).

4.

Check that the O-ring (80A) is still in good condi

-

tion

5.

Remove the housing (01).

6.

Remove the protector (47A).

7.

Place a fixed spanner in the shaft (05) planes to

avoid the rotation.

8.

Disassemble the impeller screw (25) and the

O-ring (80D).

9.

Remove the impeller (02). If necessary, give it a

thud with a plastic hammer to remove the cone.

02.002.32.0012

Maintenance

INOXPA S.A.U.

02.002.30.02EN · (0) 2021/04

18

«
...
16
17
18
19
20
...
»

Содержание M-226







































Отзывы:

Нет отзывов