INOXPA M-226 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 38

INOXPA M-226 Скачать руководство пользователя страница 17

8.7. DISASSEMBLY AND ASSEMBLY OF THE BLENDER

The assembly and disassembly of the blenders should be done by qualified personnel. Make sure

that the personnel read carefully this instruction manual and, in particular, those instructions which

refer to the work they will perform.

ATTENTION

Incorrect assembly or disassembly may cause damage in the blender’s operation and

lead to high repair costs and a long period of downtime.

INOXPA is not responsible for accidents or damages cause by a failure to comply with

the instructions in this manual.

Preparation

Provide for a clean working environment so some parts, including the mechanical seal, require very

careful handling and others have close tolerances.

Check that the parts which are used are not damaged during transport. When doing this, you need

to inspect the adjustment edge, the butted faces, the tight fit, burrs, etc.

After each disassembly, carefully clean the parts and check for any damage. Replace all damaged

parts.

Tools

Use the proper tools for assembly and disassembly operations. Use them correctly.

Cleaning

Before disassembling the blender, clean it outside and inside.

8.8. DISASSEMBLY AND ASSEMBLY OF THE HOUSING AND IMPELLER

1. Close the suction and the discharge valve.

2. Remove, sequentially, the pieces which are on

the housing (01) top: hooper (101), butterfly val

-

ve (96), distribution assembly (102) and internal

venturi (103), removing the clamps (91,91A) which

join these pieces.

3.

Remove the retention ring (15).

4.

Check that the O-ring (80A) is still in good condi

-

tion.

5.

Remove the housing (01).

6.

Loosen and remove the screws (50A) and remove

the motor shroud (14).

7. Disassemble the drive fan protection according to

the manufacturer instruction manual.

8. Fix, with a spanner, the fan shaft taking care not to

damage it, to avoid the blender shaft rotation.

9.

Remove the screw which fixes the impeller (25)

and the O-ring (80D) with a box spanner.

10.

Remove the impeller (02). If necessary, give it a

thud with a plastic hammer to remove the cone.

8.8.1. Disassembly of the housing and impeller for the M-226 blender

02.002.32.0028

Maintenance

17

INOXPA S.A.U.

02.002.30.02EN · (0) 2021/04

«
...
15
16
17
18
19
...
»

Содержание M-226







































Отзывы:

Нет отзывов