Inovance IS650P Series Скачать руководство пользователя

Страница: 26 / 102

3 Keypad and Display

- 25 -

3.2 Keypad Display

The keypad can display the running status, parameter, faults, and monitored information during running of

the servo drive.

●

Status display: Displays the current servo drive status, such as servo ready or running.

●

Parameter display: Displays function codes and their values.

●

Fault display: Displays the fault and warnings occurring in the servo drive.

●

Monitoring display: Displays the current running parameters of the servo drive.

3.2.1 Display Switchover

Figure 3-2 Switching between different display

Power-on

Status

display

Parameter

display

Monitoring

display

Fault display

MODE

Switch to

group H0B

MODE

SET

Motor static

After you set H02-32, the keypad switches over

the display automatically after motor rotation.

●

After the power is on, the keypad enters the status display mode.

●

Press key MODE to switch over between different modes, as shown in the preceding figure.

●

In status display mode, set H02-32 and select the monitored parameters. When the motor rotates,

the keypad automatically switches over to monitoring display. After the motor becomes stopped, the

keypad automatically restores to status display.

●

In parameter display mode, set group H0B and select the parameters to be monitored, and the keypad

switches over to the monitoring display mode.

●

Once a fault occurs, the keypad immediately enters the fault display mode, and all 5-digit LEDs blink.

Press key SET to stop blinking, and then press key MODE to switch over to the parameter display

mode.

Содержание IS650P Series







































































































Результаты поиска

Содержание IS650P Series

Отзывы:

Похожие инструкции для IS650P Series

Бренды по названию

Популярные бренды

Inovance IS650P Series, Руководство пользователя

Результаты поиска

Содержание IS650P Series

Отзывы:

Похожие инструкции для IS650P Series

Бренды по названию

Популярные бренды