iNO DOMINATOR Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 32

background image

5

Purpose of use

Flail mower DOMINATOR is a heavy duty professional machine, purpo-

sed for use on large agriculture and green areas, for mulching maize and
other crop residues, grass and bushes on green and abandoned areas. This
machine is very rigid and made for use in hard working conditions.

Warranty

Warranty period for the machine is 24 months.

WE DECLARE WITH FULL RESPONSIBILITY THAT THIS TYPE OF THE PRO-
DUCT FULFILLS ALL THE RELEVANT PROVISIONS OF THE FOLLOWING DI-
RECTIVES:

DIRECTIVE MACHINE 2006/42/EC

AND FOLLOWING ADDITIONS:

91/368/CEE, 93/44/CEE, 93/68/CEE

HARMONISED STANDARDS APPLIED IN ORDER TO VERIFY COMPLIANCE
WITH DIRECTIVES:

SIST-EN 292-1, SIST-EN 292-2, SIST EN ISO 4254-12:2012

A producer can ensure normal operating of the machine only

with use of original spare parts!

INO is not responsible for any damage or injuries, if the user

doesn't consider the rules in this book!

INO is not responsible for any damage or injuries due to impro-

per use of the machine!

After receiving the machine it is necessary to check that the machine

has not been injured during transport and that it is equipped with all basic
and additional equipment ( if ordered). A customer can claim any missing
or damaged part in the period of 8 days after receiving the machine.

«
...
3
4
5
6
7
...
»

Содержание DOMINATOR

































Отзывы:

Нет отзывов

Похожие инструкции для DOMINATOR

Бренд: Walker Страницы: 100

Бренд: Poulan Pro Страницы: 48

Бренд: Toro Страницы: 60

Jacobsen SLF530

Бренд: Textron Страницы: 352

Бренд: Hayter Страницы: 56

Бренд: Redexim Страницы: 12

Бренд: HUSTLER Страницы: 65

Бренд: MTD Страницы: 35

Бренд: Snapper Страницы: 18

comport plus G 44 PB

Бренд: Oleo-Max Страницы: 56

Бренд: Toro Страницы: 48

Бренд: ECLOZ Страницы: 56

Бренд: Lux Tools Страницы: 192

Бренд: IronCraft Страницы: 44

Бренд: Dolmar Страницы: 76

Бренд: Jonsered Страницы: 56

Бренд: BOX Plus Страницы: 30

Бренд: New Idea Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды