manualshive.com logo in svg

iNO DOMINATOR, Руководство по эксплуатации, Страница: 10 / 32

Поделиться
Скачать
iNO DOMINATOR Скачать руководство пользователя страница 10

 

 

10 

hydraulic  lift),  apply  the  hand  brake  and  if  the  ground  is steeply 
slooping, wedge the tractor.Take out the starting key.  

18.

 

Do not enter the zone between the tractor and the machine. It is 
strongly forbidden to be in this zone if the tractor is not properly 
disconnected, hand brake applied and starting key taken out.  

 

Attachment to the tractor and transport 

 

1.

 

Before attaching the machine or detaching it of the tractor be sure 
that hydraulic lift system is in a neutral position. 

2.

 

Check that a category of 3-point linkage on the tractor corresponds 
to that one on the machine.  

3.

 

Be careful! There is a danger of injuries when working near or with  
3-point linkage.  

4.

 

It is forbidden to be in the zone between the tractor and the ma-
chine while working with the hydraulics.  

5.

 

Put the 3-point linkage into the position that makes the moving of 
the machine impossible. 

6.

 

During  transport  secure  the  lever  of  hydralic  lift  to  avoid  any 
unplanned moving of the machine. 

7.

 

ever leave the tractor cab when the tractor is working.  

8.

 

Adjust driving speed to the road conditions. 

 

PTO drive 

 

1.

 

Use only PTO shafts with all guards, as directed by the producer.  

2.

 

All guards on PTO shaft must be in good order . 

3.

 

Take care that all guards on the PTO shaft are in proper position 
during transport or operating. Respect the producer's instructions. 

4.

 

The  PTO shaft  must  be  assembled  or diassambled  only  with  the 
engine stopped and the starting key removed.  

5.

 

The guards of the PTO shaft must be fixed to the machine and to 
the tractor with chains to prevent rotation.  

6.

 

Before starting always check that the speed and the rotational di-
rection correspond to those on the machine.  

Содержание DOMINATOR

































Отзывы:

Нет отзывов