iNO DOMINATOR Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 32

background image

26

8.

After the job is done

After the job done disconnect the PTO shaft, lift the machine and trans-

port it onto the appropriate place.

During transport reduce the speed, especially on bumpy roads.

The weight of the machine may render driving difficult and da-
mage the machine itself. During transport the machine must
be always in the central position.

PTO shaft must be disconnected during transport.

At disconnecting the machine respect the warning rules for at-
taching the machine.

Store the machine on a dry and flat ground to avoid any damage or

corrosion.

Cleaning

To avoid any corrosion clean the machine after each working day, espe-

cially working tools, bearings etc. Be careful to avoid damaging hydraulic
pipes, hydraulic cylinder, bearings and paint.

Fig. 20

«
...
24
25
26
27
28
...
»

Содержание DOMINATOR

































Отзывы:

Нет отзывов

Похожие инструкции для DOMINATOR

Бренд: Baroness Страницы: 5

Бренд: Jacobsen Страницы: 148

Бренд: Solo Страницы: 88

Бренд: Ransomes Страницы: 114

Бренд: Oleo-Mac Страницы: 332

Бренд: KUHN Страницы: 72

Бренд: McCulloch Страницы: 28

Бренд: Ferris Страницы: 60

Бренд: Toro Страницы: 2

HR 4600 Turbo 67862

Бренд: Jacobsen Страницы: 224

Бренд: Yard Machines Страницы: 27

Бренд: Honda Страницы: 24

GRASS 1265 ZSBW

Бренд: Garland Страницы: 172

Бренд: Brill Страницы: 96

Бренд: Makita Страницы: 24

Бренд: Makita Страницы: 140

Бренд: VITO GARDEN Страницы: 33

Бренд: Fieldmaster Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды