manualshive.com logo in svg

Innovx )DVW6ZLWFK#57, Руководство по установке и эксплуатации, Страница: 76 / 116

Поделиться
Скачать
Innovx )DVW6ZLWFK#57 Скачать руководство пользователя страница 76

Command Line Interface

VLAN

4-12

Innovx FastSwitch 24 Ethernet Switch 

200R205-000

Installation and Operation Manual

Issue 4

1. To configure the VLAN mode on the switch, use following command:

L2SW> Config vlan mode <none/port/dot1q>

L2SW> config vlan mode port

•

None - To disable VLAN on the switch

•

Port - Enable port-based VLAN mode, tag-based VLAN is excluded. All packets will be 
associated with default port VID before forwarding, and no tag modification (insert, 
modify or remove) will take place when the packet is transmitted out of this port. Only 
Shared VLAN (SVL) is supported in this mode.

•

Dot1q - Enable both port-based VLAN and tag-based VLAN. A default VLAN with 
VLAN ID 1 is created and assigned to all ports, once the mode is set to dot1q. 

2. To create a VLAN, use the following commands. The valid range is from 2- 4094. A 

alphanumeric name can be assigned to the created VLAN.  The maximum length of the 
alphanumeric string is  16 characters.

L2SW> config vlan create <vlanid> <name>

L2SW> config vlan create 10 Yellow

3. To add or delete a port to a new VLAN, use the following command. This command can be 

used for both port-based VLAN and Protocol based VLAN.

L2SW> config vlan  addport <vlanid> <slot.port>

L2SW> config vlan addport 10 0.1

L2SW> config vlan delport  <vlanid> <slot.port>

L2SW> config vlan delport 10 0.1

4. To remove VLAN, use the following command:

L2SW> config vlan delete <vlanid>

L2SW> config vlan delete 10

5. To configure protocol based VLAN,  use following command:

L2SW> config vlan protocol <vlanid> <protocoltype>

L2SW> config vlan protocol 10 IP

•

vlanid  - A valid VLAN ID. The valid range is 2-4094.

•

protcoltype - protocol type supported by the switch. Valid options are: 

•

None, IP, Arp, Appletalk, Appletalk_aarp, Novelll_ipx, BANYAN_VINES_C4, 
BANYAN_VINES_C5, BANYAN_VINES_AD, DECNET_MOP_01, 
DECNET_MOP_02, DECNET_DPR, DECNET_LAT, DECNET_LAVC, IBM_SNA, 
X75_INTERNET, X25_LAYER3

6. To configure the degree of participation for a specific port in a VLAN, use the following 

command:

L2SW> config vlan port pvid <vlanid> <slot.port/all>

L2SW> config vlan port pvid 10 0.1

•

vlanid  - A valid VLAN ID. The valid range is 1-4094.

•

slot.port  -physical port or trunk port, or all. .

Содержание )DVW6ZLWFK#57





















































































































Отзывы:

Нет отзывов