manualshive.com logo in svg

Innovx )DVW6ZLWFK#57, Руководство по установке и эксплуатации, Страница: 106 / 116

Поделиться
Скачать
Innovx )DVW6ZLWFK#57 Скачать руководство пользователя страница 106

Command Line Interface

SNMP

4-42

Innovx FastSwitch 24 Ethernet Switch 

200R205-000

Installation and Operation Manual

Issue 4

When SNMPv3 is enabled, the FS-24 automatically creates the following users attached to the 
initial group. The default users created by the switch may be deleted, if they are not required.

PrivateUser: authPriv privilege
AuthOnlyUser: authNoPriv privilege
PublicUser: noAuthNoPriv privilege

Special Considerations

•

To get the Authentication and Privacy Password for the default users, contact technical support.

•

The Authentication Password and Privacy Passwords are displayed in encoded form similar to 
encrypted password display in /etc/passwd file in Unix/Linux systems.

•

FS-24 supports 16 MIB views, 16 Groups and 64 Users

•

Before deleting a group all users associated with that group must be deleted and before deleting 
a view all groups using that view must be deleted.

•

FS-24 will be busy for a while computing the message digest and encrypting the password 
string when Authentication and Privacy Passwords are configured.

SNMP Trap Setup

A trap manager is a management station that receives traps (alarms and event notifications) and the 
system alerts generated by the switch. If no trap manager is defined, switch will not issue any trap. 
Create a trap manager by entering the IP address of the station and a community string, using the 
following command:

1. To add trap manager IP address and community name, use the following command.

L2SW> config snmp trap add <v1/v2c/v3> <ipaddr> <communityname/user 

name>

L2SW> config snmp trap add v3 172.30.40.202 user

Note

  SNMP v3 user name must be specified when SNMP v3 trap is configured.

2. To delete a trap configuration, use the following command.

L2SW> config snmp trap delete <v1/v2c/v3> <ipaddr>

L2SW> config snmp trap delete v3 172.30.40.202

3. To delete all traps configured in the system, use the following command.

L2SW> config snmp trap deleteall

4. To display SNMP trap settings, use the following command.

L2SW> show snmp trap

Figure 4-33

Displays SNMP Trap settings 

Содержание )DVW6ZLWFK#57





















































































































Отзывы:

Нет отзывов