Innovx )DVW6ZLWFK#57 Скачать руководство пользователя страница 59

Страница: 59 / 116

Using the Web Interface

Administrator Web Page

200R205-000

Innovx FastSwitch 24

3-37

Issue 4

Installation and Operation Manual

PerPort Configuration

With this page, user can select the specific port and configure the authorization state.

Each port can select four kinds of authorization state:

•

Fu: Force the specific port to operate in unauthorized state. Access to the network through this
port will be blocked.

•

Fa: Force the specific port to be in authorized state and allow users attached to this port to access
the network without forcing the user to go thru authentication procedure.

•

Au: The state of the specific port is determined by the outcome of the authentication.

•

No: 802.1x based port security is not supported in this port

Figure 3-5

802.1x Port Status

Содержание )DVW6ZLWFK#57





















































































































Результаты поиска

Содержание )DVW6ZLWFK#57

Отзывы:

Innovx )DVW6ZLWFK#57, Руководство по установке и эксплуатации, Страница: 59 / 116

Результаты поиска

Содержание )DVW6ZLWFK#57

Отзывы: