innove duralam INTEGRA Скачать руководство пользователя

Страница: 9 / 32

WARRANTY

sEE YOuR INNOVÉ

LOcATION Of PuRchAsE TO cONfIRM cOMPLETE wARRANTY TERMs

AND cONDITIONs. TERMs bELOw MAY VARY sLIGhTLY wIThIN EAch INNOVÉ

LOcATION.

Innové

Global solutions warrants the Duralam Integra to be free from defects in material and

workmanship for a period of 1 year for parts from date of installation. This warranty is the only warranty

made by Innové

and cannot be modified or amended. Labour is covered by the installing dealer for

a period of 1 year from date of installation unless agreed to different terms at time of purchase. These

agreed terms must be clearly marked on the invoice and are between the installing dealer and customer.

Innove

Global Solutions sole and exclusive liability and the customer’s sole and exclusive remedy under

this warranty shall be, at Innové

Global Solutions option, to repair or replace any such defective part

or product. These remedies are only available if Innové

Global Solutions examination of the product

discloses to Innové

Global Solutions satisfaction that such defects actually exist and were not caused

by misuse, neglect, attempt to repair, unauthorized alteration or modification, incorrect line voltage, fire,

accident, flood or other hazard.
Limited warranty:

This warranty specifically does not cover damage to the laminating rollers caused by knives, razor

blades, other sharp objects, failure caused by adhesives or improper use of the machine. Warranty

repair or replacement does not extend the warranty beyond the initial 90 day period from the date of

installation.
wARNING - unauthorized customer alterations will void this warranty.
The warranty made herein is in lieu of all other warranties, expressed or implied, including any warranty

of merchantability or fitness for a particular purpose. Innové

Global Solutions will not be liable for

property damage or personal injury (unless primarily caused by its negligence), loss of profit or other

incidental or consequential damages arising out of the use or inability to use the equipment.
Exclusions to the warranty:

This warranty specifically does not cover:

1. Damage to the laminating rollers caused by knives, razor blades, other sharp objects or failure caused

by adhesives.

2. Damage to the machine caused by lifting, tilting and/or any attempt to position the machine other

than rolling on the installed castors on even surfaces.

3. Improper use of the machine.

4. Damage due from unqualified person(s) servicing the machine.

QUALIFIED:

Any person(s) trained by

Innové

Global Solutions to perform service related work on such equipment.

Содержание duralam INTEGRA

































Результаты поиска

Содержание duralam INTEGRA

Отзывы:

Похожие инструкции для duralam INTEGRA

Бренды по названию

Популярные бренды

innove duralam INTEGRA, Руководство по эксплуатации

Результаты поиска

Содержание duralam INTEGRA

Отзывы:

Похожие инструкции для duralam INTEGRA

Бренды по названию

Популярные бренды