innove duralam INTEGRA Скачать руководство пользователя | Manualshive

Страница: 23 / 32

background image

23

OPERATING

fILM LOADING Continued

sTEP 7 - Threading card

• Use threading card to push film into nip of heat rollers

(Refer to Figure 23)

• Press RUN

• Monitor film as it passes through laminator. Film goes

into back pull rollers and exits. (Refer to Figure 24)

• Turn heat to correct setting. Wait for Green “Ready”

LED to light up indicating completion. Laminator is

ready to go! (Refer to Figure 25)

NOTE: Monitor threading card closely as it passes

through laminator. Threading card may curl up and not go

into pull rollers. Stop laminator if this condition occurs.

Use extra threading card to push film down to ensure

safe entry into pull rollers

fIGuRE 24

fIGuRE 23

(Threading card pushes film into

nip of rollers)

fIGuRE 25

(Film moving slowly towards

pull rollers)

fIGuRE 26 (

Threading card starting to exit

pull rollers)

fIGuRE 27

(Film is now loaded and exiting the laminator.

Wrinkles will slowly disappear as film aligns itself.)

«
...
21
22
23
24
25
...
»

Содержание duralam INTEGRA

































Отзывы:

Нет отзывов

Похожие инструкции для duralam INTEGRA

Бренд: GBC Страницы: 44

SMART LAMINATOR

Бренд: I&A SYSTEM Страницы: 7

Бренд: Martin Yale Страницы: 20

Бренд: M-Triangel Страницы: 9

Бренд: GBC Страницы: 75

Бренд: GBC Страницы: 95

Бренд: GBC Страницы: 109

Бренд: Hama Страницы: 96

Бренд: GBC Страницы: 7

Бренд: Fellowes Страницы: 52

Бренд: GBC Страницы: 42

Бренд: Fellowes Страницы: 6

Бренд: Fellowes Страницы: 11

Бренд: Fellowes Страницы: 14

Бренд: Opus Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды