innove duralam INTEGRA Скачать руководство пользователя

Страница: 31 / 32

TROUBLESHOOTING GUIDE

PROBLEM

TROUBLESHOOTING STEPS

Laminator won’t turn on 1. Check main power supply at wall outlet to make sure there is power

2. Check main on/off button to ensure it is actually turned to “on” position

3. Check breaker trip fuse located near on/off switch at back of laminator

Call for service technician to repair.

Laminator won’t heat

1. Check on/off power switch – make sure laminator is turned on and there

is power to laminator

2. Check temperature control dial on control pad. Is it at correct setting?

Call for service technician to repair.

Laminator heat rolls

won’t turn

1. Is safety shield lowered?

2. Is feed tray latch activated?

Call for service technician to repair.

Laminate not sticking

Refer to “HEAT SETTINGS” and “SPEED SETTINGS” on page 24.

Paper turning black

after lamination

Thermal paper does not work in a laminator. Some calculators and fax

machines etc... use thermal paper. Heat lamination will turn the paper black

and destroy the printing. Do not use thermal paper with heat lamination.

Film jam

Refer to “CLEARING A FILM JAM (Wrap-up) on pages 26-28.

Wrinkly output

Is the film tension too loose? Turn the top and bottom film rolls by hand

and see if they are loose turning. If tension is loose the film will not pull

tight across heat rollers causing wrinkles. Tighten tension control.

Refer to “TENSION CONTROL” on page 24.
Thin papers such as newspaper can wrinkle because the paper already

has folds and it is very thin. We do not recommend laminating archival type

documents because it may wrinkle and can’t be replaced.

Film not sealing

on the edges

This may be caused by the paper being very thick and the rollers cannot

squeeze the edges proper. Use thinner paper if this is a problem. Some

users will laminate multiple layers of paper in one pass. This is okay to do

but the edge might not be perfectly sealed.
Check for excess glue build-up on the roller edges. Refer to “CLEANING

ROLLERS” on pag 25.
If the paper is normal thickness and the edge is not sealing check the

roller gap. Look carefully between the rollers and see if you can see light

between them. The roller pressure may be out of adjustment and require

service from your local authorized dealer.

Содержание duralam INTEGRA

































Результаты поиска

Содержание duralam INTEGRA

Отзывы:

Похожие инструкции для duralam INTEGRA

Бренды по названию

Популярные бренды

innove duralam INTEGRA, Руководство по эксплуатации

Результаты поиска

Содержание duralam INTEGRA

Отзывы:

Похожие инструкции для duralam INTEGRA

Бренды по названию

Популярные бренды