Innotech Omni C14 Скачать руководство пользователя страница 48

Страница: 48 / 90

Omni Installation Instructions

Page 48

Edition 1.2 dated 20.08.2018

3-4.5.2 RS-485 Comms

The Omni U10 Comms Inputs provide the capability to connect to the host Omni controller and other

daisy-chained U10 REMs.

Connecting U10 REMs

Omni U10 REMs are connected to the Omni network via the RS-485 Comms port(s). Connection is

achieved using daisy-chaining. The first U10 is connected to a Comms port on the host C40 or C20. For

subsequent U10 REMs using an Omni controller host, the cable termination for the next U10 is done

within the same terminal connector. When the last controller is connected, ensure to set the EOL

Jumper to the correct position.

Figure 3-10:

U10 Connection to Omni

COMMS

U10 REMs are daisy

chained for connection

via the RS485 Comms.

COMMS

U10 REM final connection.

Remember to set the End Of

Line (EOL) jumper on the first

and last device on the RS-485

network.

COMMS

C40

C20

Place the jumper on

to set End of Line.

EOL Note:

In this example, the C20 and it’s REM require EOL jumpers to be set.
The C40 and the last REM require EOL jumpers to be set.

• An Omni C20 & C40 can support up to 5 daisy-chained U10 REMs. The Omni C14 does not support the U10 REM.

• EOL Jumpers are accessed inside the expansion bay on all controllers.

Omni C40 U10 Wiring

24V

U10

RS485

Comms

24V

U10*

RS485

Comms

24V

Omni C40*

RS485

Comms

*Set the EOL jumper for the first and final RS-485 device

Figure 3-11:

Omni C40 U10 Connection

Содержание Omni C14



























































































Результаты поиска

Содержание Omni C14

Отзывы:

Похожие инструкции для Omni C14

Бренды по названию

Популярные бренды

Innotech Omni C14, Руководство по установке

Результаты поиска

Содержание Omni C14

Отзывы:

Похожие инструкции для Omni C14

Бренды по названию

Популярные бренды