manualshive.com logo in svg

INIM Previdia Ultra, Руководство по установке

Поделиться
Скачать
INIM Previdia Ultra Скачать руководство пользователя страница 9

Installation manual

General information

9

1.5.3 Documents for the users

Declarations of Performance, Declarations of Conformity and Certificates concerning to INIM Electronics S.r.l. products
may be downloaded free of charge from the web address www.inim.biz, getting access to Extended Access and then
selecting “Certifications” or requested to the e-mail address [email protected] or requested by ordinary mail to the address
shown in the 

paragraph 1.5.1

.

Manuals may be downloaded free of charge from the web address www.inim.biz, getting access to Extended Access and
then selecting "Manuals".

1.5.4 Safeguard instructions

The following symbol shown on the product and/or on its packaging indicates to refer to this manual
for further information on the electrical safety of the product.

EN IEC 62368-1

Isolation class

I

Terminal type

AC INPUT

ES3, PS3

BATTERY

ES1, PS3

RELAY (IFAMPSU and IFM24160)

ES1, PS2

OUT1, OUT2 (IFAMPSU and IFM24160)

ES1, PS2

ESPANSION BOARD

ES1, PS2

RS485-BMS, RS485-REPEATER

ES1, PS2

CAN-IN, CAN-OUT

ES1, PS2

TAMPER

ES1, PS1

USB

ES1, PS1

CR2032 (J2)

ES1, PS1

RS232

ES1, PS1

LOOP-A and B (IFM2L)

ES1, PS2

ETHERNET (FPMCPU, FPAMIAS, 

IFAMIDANET and IFAMEVAC)

ES1, PS1

MUSIC 1/2 (IFAMEVAC)

ES1, PS1

AUX 1/2 (IFAMEVAC)

ES1, PS1

A/B PAGERS (IFAMEVAC)

ES1, PS2

LINE A/B (IFAMAMP)

ES3, PS3

LOCAL AUDIO (IFAMAMP)

ES1, PS1

RISER 1/2/3/4 (IFAMFFT)

ES2, PS1

Содержание Previdia Ultra













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды