Inglesina Maior, Инструкция по эксплуатации

Страница: 19 / 124

19
EN
not approved by L’Inglesina Baby S.p.A.
WHAT TO DO IF YOU REQUIRE ASSISTANCE
• If you require assistance for your product, immediately
contact the Inglesina Retailer that sold it to you, with the
“Serial Number” relative to said object ready on hand.
• It is the Retailer’s duty to contact Inglesina to assess the
best suited intervention case by case and then provide the
subsequent indications.
• The Inglesina Customer Care Service can provide any
information, following written request by filling out the
form provided on the website: inglesina.com - Warranty and
Assistance section.
HINTS FOR CLEANING AND MAINTAINING THE PRODUCT
• This product requires regular maintenance by the user.
• Never force any mechanisms or moving parts; in case of
doubt, check the instruction first.
• Do not store the product if it is still wet and do not leave it
in humid environments since mildew may form.
• Store the product in a dry place.
• Protect the product against weather agents, water, rain
or snow; moreover, continuous and prolonged exposure to
sunlight can cause changes in the colour of many materials.
• Should the product be used on the beach, carefully clean
and dry it afterwards in order to remove sand and salt as they
may cause rusting.
• Clean the plastic and metal parts with a damp cloth or with
a mild detergent; do not use solvents, ammonia or benzine.
• Carefully dry metal parts after any contact with water to
prevent the formation of rust.
• Keep all moving parts clean and, if necessary, lubricate
them with light oil.
HINTS FOR CLEANING THE TEXTILE LINING
• Seat cover and harness are surface wash only. Clean with a
damp cloth and mild soap; do not use solvents, ammonia or
bleach.
Do not use abrasive cleaners or scrubbing pads.
• Follow the lining washing instructions on the labels.
Do not bleach
Do not tumble dry
Dry flat in shade
Do not iron
Do not dry clean
Do not spin-dry
• Dry the textile lining completely before using or storing it.
LIST OF COMPONENTS
fig. 1
A
Hood
B Handrail
C Storage basket
D Rain cover (if available)
“SELF STANDING” SUPPORT
fig. 2
In order to allow the stroller to remain upright on
its own, pull out the support ( S1 ) and place it in its housing.
STROLLER OPENING
fig. 3
To open the stroller, use both levers ( P1 ) and
simultaneously, holding the handle firmly, lift the stroller
until the correct opening click is heard.
Warning: before use, make sure that the stroller is
correctly opened by checking that the red area is no
longer visible from both sides.
Caution: use the levers (P1) exclusively while opening
and closing the stroller. Be careful not to operate them
accidentally during the normal use of the stroller.
REMOVING/ATTACHING THE FRONT WHEEL ASSEMBLY
In case of need, the front wheel assembly ( D ) can be easily
removed.
fig. 4 To remove it, pull it out from the front support
while holding down the lever ( D1 ).
fig. 5 To reinstall it, simply position it and push it until it
clicks into place.
fig. 6 Caution: make sure that the wheels are properly
attached before use.
REMOVING/ATTACHING THE REAR WHEELS
Should it be necessary, the rear wheels ( E ) can easily be
removed.
fig. 7 Use a screwdriver (or similar tool, not included) to
operate the lever ( E1 ) and simultaneously pull them out from
the rear support.
fig. 8 To reinstall them, simply position them and push
them until they click into place.
fig. 9 Caution: make sure that the wheels are properly
attached before use.
REAR WHEELS BRAKE
fig. 10
To operate the brake, use the rear central lever ( P3 ).
Always engage the brake during stops.
BLOCKING/UNBLOCKING THE FRONT WHEELS
fig. 11
The stroller features swivelling wheels that can be
blocked or unblocked simply by operating the lever ( P4 ) by
the front wheel assemblies.
HANDRAIL
fig. 12
The bumper bar ( B ) can be opened on one side
or completely removed; to open it, pull the lever ( B1 ) and
remove it from its housing.
To remove it, repeat the operation on the other side as well.
Warning: never attach the bumper bar in the direction
opposite the one shown.
ADJUSTING THE BACKREST
fig. 13
To lower the backrest, release the rear strap by
pressing the button ( P5 ) on the central device ( P6 ).
fig. 14 To lift the backrest, press the button ( P5 ) on the
control device ( P6 ) and simultaneously pull the rear ring ( P7 ).
SAFETY BELTS
fig. 15
If the height of the back straps must be changed,
remove the shoulder straps ( P8 ) by detaching the velcro that
secures them on the belts ( P13 ), then pull them out of the
loops on the backrest ( P9 ). Use both back straps always at the
same height.
INSTRUCTIONS