background image

 EN-4                                                                                                                                                                                                   22204945 Rev C

EN

Indicates an imminently hazardous 
situation which, if not avoided, will result 
in death or serious injury.

WARNING

Indicates a potentially hazardous situation 
which, if not avoided, could result in death 
or serious injury.

Indicates a potentially hazardous situation 
which, if not avoided, may result in minor 
or moderate injury or property damage.

NOTICE

Indicates information or a company 
policy that relates directly or indirectly to 
the safety of personnel or protection of 
property.

GENERAL SAFETY PRECAUTIONS 

Intake air can contain carbon monoxide or other contaminants. 
Will cause serious injury or death. Ingersoll Rand air compressors 
are not designed, intended or approved for breathing air. 
Compressed air should not be used for breathing air applications 
unless treated in accordance with all applicable codes and 
regulations.

„

WARNING

A hazardous voltage can cause serious injury or death. 
Disconnect power and bleed pressure from the tank before 
servicing. Lockout/tagout machine. Compressor must be 
connected to properly grounded circuit. See grounding 
instructions in manual. Do not operate compressor in wet 
conditions. Store indoors.

Moving parts. Can cause serious injury. Do not operate with 
guards removed. Machine may start automatically. Disconnect 
power before servicing. Lockout/tagout machine. 

Hot surfaces. Can cause serious injury. Do not touch. Allow to 
cool before servicing. Do not touch hot compressor or tubing.

High pressure air. Bypassing, modifying or removing safety/relief 
valves can cause serious injury or death. Do not bypass, modify 
or remove safety/relief valves. Do not direct air stream at body. 
Rusted tanks can cause explosion and severe injury or death. 
Drain tank daily or after each use. Drain valve located at bottom 
of tank.

CAUTION

A caution risk of bursting. Use only suitable air handling parts 
acceptable for pressure of not less than the maximum allowable 
working pressure of the machine.

SAFETY

GENERAL INFORMATION

Your air compressor unit is suitable for operating air tools, caulking 
guns, grease guns, sandblasters, etc. Depending on your application, the 
following accessories may be required:

An air pressure regulator to adjust the air pressure entering the tool or 
accessory.

 An air line filter for removal of moisture and oil vapour in compressed  
air.

 An in-line lubricator to prolong the life of air tools.

 Separate air transformer which combine the functions of air regulation  
and/or moisture and dirt removal.

Contact your nearest authorized dealer or call 1-800-AIR-SERV for more 
information on air tools and accessories for your application.

RELEASED 05/Apr/2018 15:16:08 GMT

Содержание SS5L5

























Отзывы: