Ingersoll-Rand 285B Series, Информация о продукте

Страница: 3 / 36

EN
45573011_ed5 EN-1
Product Safety Information
Intended Use:
These Air Impact Wrenches are designed to remove and install threaded fasteners.
For additional information refer to Product Safety Information Manual Form 04580916.
Manuals can be downloaded from ingersollrandproducts.com.
Product Specifications
Tools running at 90 PSI Air Pressure
Models Style
Drive
Impacts
per Min.
Recommended
Torque Range
Sound Level dB(A)
(EN ISO 15744)
Vibration (m/s²)
(EN ISO 28927-2)
Type Size ft-lbs (Nm) † Pressure (L
p
) ‡ Power (L
w
) Level *K
285B
Inside
Trigger
Square 1” 700
100-900
(136-1220)
103.4 114.4 8.0 1.2
285B-6
Inside
Trigger
Square
6” extended
1” 700
100-900
(136-1220)
103.4 114.4 9.0 2.7
285B-S6
Inside
Trigger
Spline
6” extended
#5 700
100-900
(136-1220)
103.4 114.4 9.0 2.7
285B-6-AP
Outside
Trigger
Square
6” extended
1” 700
100-900
(136-1220)
103.4 114.4 9.0 2.7
295A
Pistol
Grip
Square 1” 700
100-900
(136-1220)
101.1 112.1 8.6 1.0
295A-6
Pistol
Grip
Square
6” extended
1” 700
100-900
(136-1220)
101.1 112.1 9.1 2.9
Tools running at 120 PSI Air Pressure
Models Style
Drive
Impacts
per min.
Recommended
Torque Range
Sound Level dB(A)
(EN ISO 15744)
Vibration (m/s²)
(EN ISO 28927-2)
Type Size ft-lbs (Nm) † Pressure (L
p
) ‡ Power (L
w
) Level *K
285B
Inside
Trigger
Square 1” 830
120-1080
(163-1464)
107.0 118.0 16.5 3.4
285B-6
Inside
Trigger
Square
6” Extended
1” 830
120-1080
(163-1464)
107.0 118.0 13.3 2.1
285B-S6
Inside
Trigger
Spline
6” Extended
#5 830
120-1080
(163-1464)
107.0 118.0 13.3 2.1
285B-6-AP
Outside
Trigger
Square
6” Extended
1” 830
120-1080
(163-1464)
106.2 117.2 13.3 2.1
295A
Pistol
Grip
Square 1” 830
120-1080
(163-1464)
102.5 113.5 12.7 2.5
295A-6
Pistol
Grip
Square
6” Extended
1” 830
120-1080
(163-1464)
102.5 113.5 12.3 3.8
† K
pA
= 3dB measurement uncertainty
‡ K
wA
= 3dB measurement uncertainty
* K = measurement uncertainty (Vibration)
WARNING
Sound and vibration values were measured in compliance with internationally recognized test standards. The exposure to the user in
a specific tool application may vary from these results. Therefore, on site measurements should be used to determine the hazard level
in that specific application.
Installation and Lubrication
Size air supply line to ensure tool’s maximum operating pressure (PMAX) at tool inlet. Drain condensate from valve(s) at low point(s) of piping,
air filter and compressor tank daily. Install a properly sized Safety Air Fuse upstream of hose and use an anti-whip device across any hose
coupling without internal shut-off, to prevent hose whipping if a hose fails or coupling disconnects. See drawing 47132790 and table on page 2.
Maintenance frequency is shown in a circular arrow and defined as h=hours, d=days, and m=months of actual use. Items identified as:
1. Air filter 5. Hose diameter 9. Oil
2. Regulator 6. Thread size 10. Grease - during assembly
3. Lubricator 7. Coupling
4. Emergency shut-off valve 8. Safety Air Fuse
Parts and Maintenance
When the life of the tool has expired, it is recommended that the tool be disassembled, degreased and parts be separated by material so that
they can be recycled.
Original instructions are in English. Other languages are a translation of the original instructions.
Tool repair and maintenance should only be carried out by an authorized Service Center.
Refer all communications to the nearest
Ingersoll Rand
Office or Distributor.