Ingersoll-Rand 2115P4Ti, Инструкция по эксплуатации

Страница: 1 / 36

Instructions for Model 2115P4Ti Ultra Duty
Impact Wrench
NOTICE
Model 2115P4Ti Impact Wrench is designed for use in light assembly work and machinery maintenance.
WARNING
• IMPORTANT SAFETY INFORMATION ENCLOSED - SAVE THESE INSTRUCTIONS.
• Read and understand this manual before operating this product.
• It is your responsibility to make this safety information available to others that will
operate this product.
• Failure to observe the following warnings could result in injury.
PLACING TOOL IN SERVICE
• Always install, operate, inspect and maintain this
product in accordance with all applicable standards and
regulations (local, state, country, federal, etc.).
• Always use clean, dry air at 90 psig (6.2 bar/620 kPa)
maximum air pressure at the inlet. Higher pressure may
result in hazardous situations including excessive speed,
rupture, or incorrect output torque or force.
• Be sure all hoses and fittings are the correct size and are
tightly secured. See Dwg. TPD905-2 for a typical piping
arrangement.
• Ensure an accessible emergency shut off valve has been
installed in the air supply line, and make others aware of
its location.
• Do not use damaged, frayed or deteriorated air hoses
and fittings.
• Keep clear of whipping air hoses. Shut off the
compressed air before approaching a whipping hose.
• Always turn off the air supply, bleed the air pressure and
disconnect the air supply hose before installing,
removing or adjusting any accessory on this tool, or
before performing any maintenance on this tool or any
accessory.
• Do not lubricate tools with flammable or volatile liquids
such as kerosene, diesel or jet fuel. Use only
recommended lubricants.
• Use only proper cleaning solvents to clean parts. Use
only cleaning solvents which meet current safety and
health standards. Use cleaning solvents in a well
ventilated area.
• Keep work area clean, uncluttered, ventilated and
illuminated.
• Do not remove any labels. Replace any damaged label.
USING THE TOOL
• Always wear eye protection when operating or
performing maintenance on this tool.
• Always wear hearing protection when operating this tool.
• Always use Personal Protective Equipment appropriate
to the tool used and material worked. This may include
dust mask or other breathing apparatus, safety glasses,
ear plugs, gloves, apron, safety shoes, hard hat and other
equipment.
• When wearing gloves always be sure that the gloves will
not prevent the throttle mechanism from being released.
• Prevent exposure and breathing of harmful dust and
particles created by power tool use.
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
- lead from lead based paints,
- crystalline silica from bricks and cement and other
masonry products, and
- arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
• Keep others a safe distance from your work area, or
ensure they use appropriate Personal Protective
Equipment.
• This tool is not designed for working in explosive
environments, including those caused by fumes and
dust, or near flammable materials.
• This tool is not insulated against electric shock.
• Be aware of buried, hidden or other hazards in your
work environment. Do not contact or damage cords,
conduits, pipes or hoses that may contain electrical
wires, explosive gases or harmful liquids.
Form P7748-1
Edition 1
February, 2004
CCN 04580700
Refer All Communications to the Nearest Ingersoll-Rand
Office or Distributor.
©
Ingersoll-Rand Company 2004
Printed in U.S.A
EN