background image

 

 

   

NOTICE 

When using only one SAM card, it is recommended to insert SAM1 slot (bottom). 

NOTICE 

The appearance of the sockets of SIM card and SAM is same. Please do pay attention to 
the SIM card socket position 

4.3.2

 

Micro SD Memory Card 

CAUTION: 

Switch off the terminal before opening the trapdoor. 

Micro  SD  connector  is  located  inside  the  terminal,  in  a  closed 
compartment.

 

 

 

Turn the terminal and remove the trapdoor. 

 

Micro  SD  are  identified  by  the  engraved  marks  on  the  lower 
housing. 

 

Push the cover backwards and open it. Insert Micro SD card and 
then close the cover and pull forwards. Be sure to put the Micro 
SD  contacts  downside  and  the  cut  corner  as  indicated  on  the 
figure. 

 

Close the trapdoor. 

The terminal supports Micro SD up to 32GB. 

4.4

 

Paper roll 

4.4.1

 

Main characteristics of APOS A8 paper roll 

4.4.2

 

Installing paper roll 

 

Open the paper cover by lifting the catch located at the top of APOS A8 and pull the 
cover to the rear of the terminal. 

 

Insert  the  paper  roll  in  the  compartment  following  the  directions  shown  on  the 
below picture. 

 

Pull the paper up to the top of terminal, maintain the paper and close the cover 

 

Press  simultaneously  on  both  upper  corners  of  the  paper  flap  until  it  clips  into 
position. 
 

Paper roll characteristics 

Precisions 

Color 

White 

Width 

58mm 

Diameter 

40mm 

Length 

About 18 meters 

Содержание APOS A8

















Отзывы: