INFODRAW MRS-400 страница 70 Скачать руководство пользователя

Страница: 70 / 194

July 14, 2013

INFODRAW MRS-400 User Manual v5.4.1

Microphone:

Items:

Descriptions:

“Enabled” box

Enable/Disable your computer’s microphone, by ticking or un-ticking
the box.

“Device” list box

Select from the

“Device”

list box, which connected microphone you

would like to use.

Signal

Use the

“Signal”

bar to test your microphone. If the green bar is

moving, then your microphone is working.

Detect Noise

This option enables you to not send noise below the detected noise
level. When detecting noise you must not speak and allow the
monitor to calculate the maximal noise received by the microphone.

Announcement (Disable) If you enable this option, It means that the MRS monitor will send

everything it receives from the microphone.

Conversation (Enable)

If you enable this option, It means that the MRS monitor will only
send noise if its level is above the detected noise level.

Once you have finished, press

“OK”

Right click on the

“Microphone is off”

item under “My Monitor”. Then select

“Properties”

The

“Select Audio Input

Device”

window will appear.

The descriptions of the
settings are listed below.

Содержание MRS-400



































































































































































































Результаты поиска

Содержание MRS-400

Отзывы:

Похожие инструкции для MRS-400

Бренды по названию

Популярные бренды

INFODRAW MRS-400, Руководство пользователя

Результаты поиска

Содержание MRS-400

Отзывы:

Похожие инструкции для MRS-400

Бренды по названию

Популярные бренды