manualshive.com logo in svg

Infinova V6812IR-H0 Series, Руководство пользователя

Поделиться
Скачать
Infinova V6812IR-H0 Series Скачать руководство пользователя страница 8

25 

4.3.7 IGMP Settings 

 

Figure 4-15 IGMP Settings 

V6812IR-H0 series camera supports multicast function. In the IGMP interface, 
users can select the stream type and set the state, multicast IP address and RTP 
port.  
 

4.3.8 SIP Settings 

 

Figure 4-16 SIP Settings 

26 

SIP Server

: to configure SIP server for device; 

SIP Server IP: the IP address of SIP server; 
Port: the port number of SIP server; 
Server ID: the ID of SIP server; 
Device ID: the device ID used for registration with SIP server; 
Alarm ID: the ID registered for device alarm;   
Register Interval: the interval for re-registration of device in seconds;   
Heat Beat Interval: the interval to send heat beat information by the device in 
seconds;  
After configuration completed, click Save and the device sends a registration 
request to the server.   
 

Position Information

: the mounting information or instruction for device. 

Longitude: the longitude of mounting position, as precise to two places of 
decimal; 
Latitude: the latitude of mounting position, as precise to two places of decimal. 
 

27 

4.4 Camera Settings 

Click “Camera” in the navigation bar to enter the interface shown as below: 

 

Figure 4-17 Basic Settings   

 

4.4.1 Basic Settings 

You can set the following parameters:   
Flicker frequency: 50Hz or 60Hz.   
CVBS: it automatically changes with the flicker frequency.   
Enable or disable backlight compensation or digital WDR.   
Exposure set, scene, AGC, auto aperture, shutter speed and manual AGC can 
also be set in this interface. 
Exposure Set: Manual, Scene and Shutter Priority available. In Scene mode, 
indoor or outdoor can be selected and AGC can be set (maximum 64X); if set to 

28 

Manual mode, shutter speed can be set from 

1/30s to 1/8000s

 and manual AGC 

can be set to 

1X to 64X

, yet the scene and AGC are nonadjustable; if set to 

Shutter Priority mode, the shutter speed and AGC can be set.   
Auto aperture: to enable or disable auto iris.   
Contrast Enhance: 1~6 levels match with 6 kinds of Gamma curve separately. If 
it is set to Auto, the system will adjust automatically. 
AE target: set AE target level. It can adjust video brightness via AE target setup. 
 

4.4.2 Effect Settings 

In the Effect Settings interface, users can adjust the brightness, sharpness, hue, 
contrast, saturation and 3D denoise in two ways: General or Mode, as shown in 
the figure below:   

 

Figure 4-18 Effect Set - General   

Содержание V6812IR-H0 Series















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды