background image

 

22 

Non-PTZ Mode 

Keyboard Key 

NVR Function 

[FAR/

Under non-PTZ status, switch among multiple images when previewing them. 

Note: Divide the screen into 1/4/9/16 screens, but into 8 screens. 

Joystick Up 

Select upwards within a control. 

Joystick Down 

Select downwards within a control. 

Joystick Left 

Select leftwards within a control. 

Joystick Right 

Select rightwards within a control. 

[ACK/ENTER] 

Confirm the current operation. 

[ARM/POWER] 

After the host is connected to power supply, press it to power on the device/ press and hold for 10 seconds to 

power off the device. 

[F1] 

In a menu interface, move the cursor backwards. 

[F2] 

In a menu interface, move the cursor backwards. 

[USER] Reserved. 

[SITE] Reserved. 

 

PTZ Mode

 

Keyboard Key

 

NVR Function

 

[CLEAR/ESC] 

Exit the current interface. 

[NEAR/*] 

Under PTZ mode, it means “focal ”. 

[TELE/PTT] 

Under PTZ mode, it means “zoom +”. 

[SHOT/PRST] (OPER position) 

Under PTZ mode, call a preset.   

[CLOSE/PTZ] 

Enable PTZ mode. 

[WIDE/SYS] 

Under PTZ mode, it means “zoom -”. 

[FAR/

Under PTZ mode, it means “focal length -”. 

Joystick Up 

Under PTZ mode, turn the pan/tilt upwards. 

Joystick Down 

Under PTZ mode, turn the pan/tilt downwards. 

Joystick Left 

Under PTZ mode, turn the pan/tilt leftwards. 

Joystick Right 

Under PTZ mode, turn the pan/tilt rightwards. 

[F1] 

Decrease PTZ step size. 

[F2] 

Increase PTZ step size. 

[SHOT/PRST] (PROG position) 

Under PTZ mode, set a preset. 

91+ [SHOT/PRST] (PROG position) 

Under PTZ mode, set/save autopan 1. 

91+ [SHOT/PRST] (OPER position) 

U nder PTZ mode, call autopan 1. 

Numeric key+ [RUN]+ [ACK] 

Under PTZ mode, perform tour. 

Note: Press [1]+ [RUN]+ [ACK] to call automatic cruise PATH2. 

34+ [SHOT/PRST] (OPER position) 

Under PTZ mode, home automatically. 

99+ [SHOT/PRST] (OPER position) 

Under PTZ mode, scan automatically. 

92+ [SHOT/PRST] (PROG position) 

Under PTZ mode, set/save autopan 2. 

92+ [SHOT/PRST] (OPER position) 

Under PTZ mode, call autopan 2. 

93+ [SHOT/PRST] (PROG position) 

Under PTZ mode, set/save autopan 3. 

93+ [SHOT/PRST] (OPER position) 

Under PTZ mode, call autopan 3. 

Содержание V2117

































Отзывы: