3.4 Setting and Calling up a Pattern
Pattern is the patrol record of dome and could be applied by
keyboard. Dome could record horizontal, vertical and zoom
operation and it could repeat the recorded operation accurately when
applied. This identity could be used to define normal route.
Under INFINOVA, PELCO-D/P, Up the Coax protocols, dome
could define and store 4 independent patterns.
You can set the title of a pattern through the menu of PATTERN
SET and clear the title via OSD SETUP. And the defining and
calling up the pattern can be performed by using V2117 system
keyboards.
Below is the way to define and call pattern under different
protocols.
The following are guidelines for defining and calling these four
patterns with Infinova V2117 system keyboards under INFINOVA
protocol.
To define a pattern
1.
Place the key switch at the PROGRAM position;
OPERATE
PROGRAM
MENU
2.
Enter "70, SHOT" or "1,PATRN" to start recording Pattern 1;
7
0
SHOT
OR
1
PATRN
3.
Use the joystick to perform a series of pan, tilt and zoom
operations to finish a navigation course;
Pan Left
Zoom In
Example
4. Enter "70", and then press the SHOT key or “1 PATRN” to save
the navigation course as the pattern, for Pattern 1;
7
0
SHOT
5. If pattern 2 is needed, Enter "71, SHOT" or "2, PATRN" to start
recording Pattern 2 (or otherwise skip to step 11);
7
1
SHOT
OR
2
PATRN
6. Repeat step 3 to finish the course. Enter "71, SHOT" or “2
PATRN” to save Pattern 2;
7. If pattern 3 is needed, Enter "72, SHOT" or "3, PATRN" to start
recording Pattern 3 (or otherwise skip to step 11);
7
2
SHOT
OR
3
PATRN
8. Repeat step 3 to finish the course. Enter "72, SHOT" or “3
PATRN” to save Pattern 3;
9. If pattern 4 is needed, Enter "73, SHOT" or "4, PATRN" to start
recording Pattern 4 (or otherwise skip to step 11);
7
3
SHOT
OR
4
PATRN
10. Repeat step 3 to finish the course. Enter "73, SHOT" or “4
PATRN” to save Pattern 4;
11. Place the key switch at the OPERATE position;
OPERATE
PROGRAM
MENU
To recall a pattern once
1.
Place the key switch at the OPERATE position;
OPERATE
PROGRAM
MENU
2.
Enter one of the following code combinations to recall up the
designated pattern:
z
Enter "70, SHOT" or "1,PATRN" to recall Pattern 1;
7
0
SHOT
OR
1
PATRN
z
Enter "71, SHOT" or "2,PATRN" to recall Pattern 2;
7
1
SHOT
OR
2
PA TRN
z
Enter "72, SHOT" or "3,PATRN" to recall Pattern 3;
7
2
SHOT
OR
3
PATRN
z
Enter "73, SHOT" or "4,PATRN" to recall Pattern 4.
7
3
SHOT
OR
4
PATRN
To recall a pattern repeatedly
1.
Place the key switch at the OPERATE position;
2.
Enter one of the following code combinations to recall the
designated pattern repeatedly:
Enter "69, SHOT" + "70, SHOT" to recall Pattern 1 repeatedly;
Enter "69, SHOT" + "71, SHOT" to recall Pattern 2 repeatedly;
Enter "69, SHOT" + "72, SHOT" to recall Pattern 3 repeatedly;
Enter "69, SHOT" + "73, SHOT" to recall Pattern 4 repeatedly;
The following are guidelines for defining and calling these four
patterns with Infinova V2117 system keyboards under PELCO-D/P
protocols.
To define a pattern
1. Place the key switch at the PROGRAM position;
OPERATE
PROGRAM
MENU
2. Enter "70, SHOT" OR "1,PATRN" to start recording Pattern 1;
7
0
SHOT
OR
1
PATRN
3. Use the joystick to perform a series of pan, tilt and zoom
4
