background image

Operation Guide 

 

 

Rev 2.0 (p/n: 17140724)

 INDUSTRIAL 

SCIENTIFIC 

35 

Maintenance 

With normal routine maintenance the MX4 can be relied upon to provide 
years of dependable service. The following guidelines should be followed 
when performing maintenance on the MX4. 

Cleaning 

When necessary, wipe the outside of the MX4 with a soft, clean cloth. 
Never use solvents or cleaning solutions of any type. Make sure the 
sensor diffusion membrane is free of debris. Clean sensor openings with a 
soft, clean cloth or soft brush. 

Charging the Li-ion Battery Pack 

The lithium-ion (Li-ion) battery pack should be fully charged before using 
the MX4. A cradle type charger is provided to facilitate battery charging. 
To charge the internal battery, place the MX4 upright and facing forward 
in the charging cradle. The battery icon will start to cycle from empty to full 
to indicate that the battery is charging. The battery indicator will show full 
when the instrument battery is fully charged. 

A full battery recharge can be completed in less than 7 hours. 

Battery Replacement 

Important:

 Before replacing the rechargeable battery pack, changing the 

alkaline batteries, or removing the back cover, always be sure to first turn 
off the MX4.  

The MX4 can be powered using a rechargeable battery pack or a 
replaceable alkaline battery pack. The battery pack is held in place with 
four (4) screws. For replacement parts and part numbers, refer to the 
replacement parts list later in this manual.  

The battery pack is removed by loosening the four lower screws on the 
case back and removing the pack. The new pack should be reassembled 
to the instrument chassis in a likewise manner taking care to securely 
tighten the screws. 

Warning:

 Be sure to insert the alkaline batteries with the correct positive 

“+” and negative “-“ orientation. Failure to follow proper battery orientation 
will result in damage to the instrument. Replace only with approved 
battery types. Do not mix different types of batteries together. 

Содержание MX4 iQuad













































Отзывы: