#
#
Weather conditions (rain, fog etc.)
Major obstacles outdoors
Remove the outdoor station[20] from the protective cover [32].
Hold the protective cover in the desired location, mark the position
of the two fitting holes to be drilled [36] and of a hole for the cable
if necessary [35].
Drill the two fitting holes and insert two plugs [39] if required.
If necessary, drill a suitable hole through which to feed the cable
for the power supply to the door intercom and any other
connection cables for the optional door release and/or external
signal generator (e.g. an external bell) and/or optional button for
opening the door.
A flush-mounted socket in the wall directly behind the cable
opening may be helpful to make cable connection easier.
Feed all the connection cables required through the drilled hole
and through the cable opening in the protective cover.
Fix the protective cover to the wall using two screws [38].
Carefully lever the plastic cover off the name plate [19], remove
the name plate, label it, re-insert the name plate and replace the
plastic cover over it.
If batteries are to be used (see fig. D):
Release the battery compartment cover [30] screw and lever
the cover from the outdoor station.
Insert 2 pcs. LR14 (C), 1,5 V alkaline batteries (not supplied)
into the battery compartment, paying attention to the polarity.
Do not use rechargeable batteries.
Refix the cover onto the outdoor station with the screw.
If the door intercom is used with batteries, the camera
image cannot be manually switched on, because the door
intercom is factory set to energy saving mode, it cannot receive
signals from the mobile unit. To enable manual switching on
the camera image, the door intercom must be switched to
energy consumption mode (see chapter 11.2).
If connecting a power supply unit and/or other devices, follow
connection diagrams B and C:
Only one wire should be inserted into each terminal
connection. A maximum of 2 J-Y(St)Y wires with a diameter of
0.6 twisted together may, however, be inserted into one
terminal. With three wire ends, a terminal strip or connector
must be used to join the wires before the terminal connection.
The exposed wire end (10-12 mm) must be inserted fully into
the terminal connection.
To connect a 9-12 V DC power supply unit, attach the two wires
of the supply unit to the GND and DC9-12V power connection
terminals [26].
The door intercom must not be
8. Fitting, connecting and starting up
the outdoor station
!
!
!
!
!
!
!
!
!
!
!
!
!
#
#
!
Note:
Note:
Notes:
Note:
operated with batteries AND the power supply
unit at the same time!
Remove the protective foil from the battery.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
If you are using an optional door release with its own power
supply, connect it with two wires to terminals [26] NO/COM
(max. 1 A at up to 15 V AC/DC). Please also follow the
information provided in the door release operating instructions.
If you are using an optional external signal generator with its own
power supply, connect it with the two wires for the signal
generator connection [31] (normally open contact, max. 1 A at
up to 15 V AC/DC, DVT60T2: only reacts to pressing the upper
doorbell button).
If you are not using the connection cables [31] for the external
signal generator, cut them off immediately next to the connection
terminals.
If you are using an optional button to open the door, connect it
with two wires to the terminals [26] "Taster für TÖ" and GND.
Screw the connection cover [40] in place on the door intercom
with the four screws supplied [37]so that any cables come out at
the bottom of the intercom over the angled surface.
Push the outdoor station into the protective cover [32] and
tighten it using the torx screwdriver [42] and the torx screw [41].
that if batteries are to be used, any cables should have
enough slack that the outdoor station can be removed in order to
change the batteries.
If operating with the power supply unit, connect it to 230 V AC.
When a connection is made to the power supply, the light on the
ring button [24] turns green.
Remove the protective foil from the camera lens [23].
Connect the low voltage plug on the power supply unit [17]
provided to the power supply unit connection [13] on the
charging station [14].
Plug the power supply into a suitable power socket; the power
indicator [15] turns blue.
Open the battery compartment [11] on the mobile unit.
Insert the lithium battery provided with the terminals in the
correct position.
Close the battery compartment again.
Remove the protective film from the screen [6].
Place the mobile unit on the charging station. Charging of the
lithium battery begins automatically when the mobile unit is
place on the charger.
Before using for the first time, allow the mobile unit to charge up
fully for 5 hours.
Note
Note:
9. Connection of the mobile unit
GB - 33
