manualshive.com logo in svg

Incite Fire SEC-HIM-35, Руководство по эксплуатации продукта, Страница: 2 / 21

Поделиться
Скачать
Incite Fire SEC-HIM-35 Скачать руководство пользователя страница 2

Incite Hochiki-Securiton Interface Module– Rev 1.0 

Page 2 of 21 

 

Index

 

1

 

General.................................................................................................................................................... 3

 

2

 

Modules .................................................................................................................................................. 3

 

2.1

 

SEC-HIM-35 ........................................................................................................................................... 3

 

2.2

 

SEC-HIM-35B ........................................................................................... 

Error! Bookmark not defined.

 

2.3

 

SYNCRO-SECRDU and TAKTIS-SECRDU .................................................................................................. 4

 

3

 

Operation: ............................................................................................................................................... 5

 

3.1

 

Alarm: .................................................................................................................................................... 5

 

3.2

 

Fault Mode: ........................................................................................................................................... 5

 

3.3

 

Controls: ................................................................................................................................................ 5

 

3.3.1

 

Reset: ................................................................................................................................................ 5

 

3.3.2

 

Disable: ............................................................................................................................................. 5

 

4

 

Configuration: ......................................................................................................................................... 6

 

4.1

 

SEC-HIM-35 and SEC-HIM-35B .............................................................................................................. 6

 

4.2

 

SYNCRO-SECRDU and TAKTIS-SECRDU .................................................................................................. 6

 

4.2.1

 

Unit addresses .................................................................................................................................. 6

 

4.2.2

 

Config Switch: ................................................................................................................................... 6

 

5

 

FIP Configuration ..................................................................................................................................... 7

 

5.1

 

General .................................................................................................................................................. 7

 

5.2

 

SEC-HIM-35 ........................................................................................................................................... 8

 

5.3

 

SEC-HIM-35B ....................................................................................................................................... 10

 

5.4

 

SYNCRO-SECRDU ................................................................................................................................. 11

 

5.4.1

 

I/O Setup and Attributes ................................................................................................................. 11

 

5.4.2

 

Syncro Cause and Effect Programming ........................................................................................... 13

 

5.5

 

TAKTIS-SECRDU .......................................................................................

Error! Bookmark not defined.

 

5.5.1

 

I/O Setup and Attributes ................................................................................................................. 14

 

5.5.2

 

Taktis Cause and Effect Programming ............................................................................................ 16

 

6

 

Installation ............................................................................................................................................ 17

 

6.1

 

SEC-HIM-35, SEC-HIM-35B .................................................................................................................. 17

 

6.2

 

SYNCRO-SECRDU and TAKTIS-SECRDU ................................................................................................ 19

 

6.2.1

 

Syncro Installation .......................................................................................................................... 19

 

6.2.2

 

Taktis Installation ............................................................................................................................ 19

 

6.2.3

 

Cabling ............................................................................................................................................ 20

 

 

 

 

Содержание SEC-HIM-35






















Отзывы:

Нет отзывов