manualshive.com logo in svg

In-situ Level TROLL 400, Руководство оператора, Страница: 22 / 85

Поделиться
Скачать
In-situ Level TROLL 400 Скачать руководство пользователя страница 22

1-800-446-7488

22

www.in-situ.com

1

Dust cover for the USB connection

2

Connection status

Red (flashing)

= The communication device, instrument, and Bluetooth-enabled device are not

connected.

Red (continuous)

= The communication device and instrument are connected, but the communication

device is not connected to the Bluetooth-enabled device.

-OR-

The communication device is connected via USB cable.

Green (flashing)

= The communication device is connected to the Bluetooth-enabled device, but is not

connected to the instrument.

Green (continuous)

= The communication device, instrument, and Bluetooth-enabled device are

connected.

3

On/Off button

4

Battery charge status:

100% -90%

90% - 75%

75% - 50%

50% - 25%

Less than 25%

5

Cable connector to the instrument

6

Lanyard connector

7

Serial number

8

USB connection to a power source for charging the internal battery or wired connection to a computer

Contents

l

Wireless TROLL Com

l

USB cable

l

AC wall charger (U.S.A. only, universal charger sold separately)

l

Lanyard

Charging the Communication Device

1. Remove the protective cover from the USB slot.

2. Connect the USB cable to the device.

3. Plug the USB cable into the wall charger or a powered USB port such as a computer that has a charger plugged in.

4. The device lights will turn on and blink according to charge level.

A fully-charged communication device will run for up to 40-50 continuous hours.

Battery Tips

The communication device uses an internal, rechargeable Lithium-ion (Li-ion) battery to supply power. While these batteries
last for years with minimal decrease in performance, there are a few tips to prolong the life of the battery.

Содержание Level TROLL 400






















































































Отзывы:

Нет отзывов