background image

 

1.4 IDA In-Line Deflagration Arrester Certification

The IDA certification is optional. Contact Imperial

Systems to verify if your CMAXX is equipped with the

IDA certification.

The CMAXX using the Proprietary DELTAMAXX IDA

Filters is proven to completely isolate flame transmission

and stop combustion from passing through the filters.

With IDA you can safely return air back into the workplace.

This flame and deflagration isolation meets at least

one of the required methods required by NFPA. Third

party test results are available upon request.

To maintain IDA certification on collector, you must:

• Provide a dust sample for KST testing or provide a
   copy of a completed KST test.

• Dust cannot exceed a rating of 200 KST.

• Use Certified DELTAMAX IDA Filters.

• Differential pressure cannot exceed 5 Inches of
   Water Column.

• Install a broken bag detector in return air duct.

• Install a burst indicator on pressure relief panel.

• Ground the Dust Collector

In the event of a deflagration the following must be

performed before the unit is returned to service.

1. Inspect unit for any deformation, or stress cracks.

2. Inspect tube sheet to verify there is no deforming,

and filters will seal against it properly.

3. Inspect door hardware for proper function, verify

there is no deformation or stress cracks in latch mechanism.

4. Inspect lift rails for proper function.

5. Replace filters with Certified DELTAMAXX IDA

Filters. Filters can only be purchased from Imperial

Systems.

6. Replace pressure relief panel and burst indicator.

7. Replace door gasket.

8. Replace explosion vent braces.

Imperial Systems does offer an inspection service to

verify your collector is operational. Please contact your

sales representative for current pricing.

 

1.5 Fire Protection And Safety Equipment

The customer assumes the responsibility to contact

their insurance company and or AHJ (Authority having

Jurisdiction) to see what is required to meet the needs

of fire protection, explosion ventilation, deflagration,

isolation and any other related equipment.

It is the customer’s responsibilities to relay this

information to Imperial Systems so that we can properly

select and size the necessary equipment to meet their

requirements.

The customer should adhere to any and all NFPA,

OSHA, federal, state, codes, rules, and regulations.

imperialsystemsinc.com 

    

 

   Imperial 

Systems 

Inc.

WARNING

Prevent serious injury or death.

Not following above requirements will void

IDA rating and could result in property

damage, death, or serious injury.

Содержание CMAXX





























Отзывы: