background image

11

Parity: none

Stop bit: 1

Flow control: none.

An example of transmission is shown here below: 

Pocket ultrasonic tester – Ver Version 00.01.001 
------------------------------ 
N. Date     Time     S Measure
0000 07/10/10 16:03.00 X 0055.0
0001 07/10/10 16:03.00 X 0050.6
0002 07/10/10 16:03.00 X 0050.7
0003 07/10/10 16:03.00 X 0050.7
0004 07/10/10 16:04.00 Y 0055.4
0005 07/10/10 16:04.00 Y 0055.3
0006 07/10/10 16:05.00 Y ----.-
0007 07/10/10 16:05.00 Y 0050.6
0008 12/10/10 10:34.00 A 0004.8
0009 12/10/10 10:34.00 A 0004.6
0010 12/10/10 11:29.00 C 0000.0
#####

The list of measures is more complete than the one that is displayed on the appliance because, in addition to 
the  previously  mentioned  values,  it  shows  also  when  (the  time)  the  measures  have  been  taken.  Moreover, 
the measures with negative results are also listed. 

After the transmission, the data are not deleted from the tester and, therefore, they remain at disposal for 
further uses. However, they can be manually deleted through the proper menu. 
To avoid interferences with the results, it is advisable to keep the mini USB cable always disconnected from 
the tester during the measuring phase.  

2.09  CONNECTIONS 

The tester is provided with two sets of outwards connections. In the upper part there are: 

Mini USB connector: for the communication with the host PC and for the data download;

6 mm circular connector: for the connection with the battery charger provided with the equipment.

In the lower part there are the signal connectors: 

TX:  terminal for the connection of the transmitting probe;

RX:  terminal for the connection of the receiving probe;

Trigger: synchronization signal for the oscilloscope visualization

••••

Scope: analog signal visualization received by the tester.

N.B. 

PLEASE  DO  NOT  CONNECT  THE  TERMINAL  TX  WITH  RX  USING  THE  CABLES  OF  THE 
PROBES

In  order  to  recharge  the  batteries,  always  and  only  use  the  battery  charger

provided  with  the  kit.  In  case  of  fault  or  malfunction,  contact  the
manufacturer/reseller to change the battery charger itself.

Never  connect  the  battery  charger  to  the  appliance  if  the  batteries  are  not

www.impact-test.co.uk     

      www.impact-test.com      

 www.impact-testsets.co.uk 

Содержание CN842
















Отзывы: