Immergas VICTRIX 26 2 I Скачать руководство пользователя страница 60

Страница: 60 / 62

STV2I ed 11/09

VICTRIX 2 I Export

Technical Documentation

ERROR 15

Wiring configuration error

N.B.: This board can be used for instant type boilers (VICTRIX 26 2 I) or with

storage tank (VICTRIX X 12 - X 24 2 I). The board automatically recognises the

type of boiler by means of the relative wiring.

The board is configured as instant boiler.

(NO jumper between clamps 7-8 of connector X8).

For the VICTRIX 26 2 I boiler check there is NO PRESENCE of the

connection jumper between clamps 7-8 of the connector X8.

Yes

Replace the P.C.B.

ERROR 16

Fan anomaly

The wiring between the P.C.B. and fan is OK.

Check continuity of the cable on clamp 5 of connector X12.

Restore the electric connection/replace the wiring.

Yes

Replace the fan. If the anomaly persists, replace the P.C.B.

At least 24 VDC is present to clamps 3-1 of the connector X12.

Replace the P.C.B.

Yes

The wiring between the P.C.B. and fan is OK.

Restore the electric connection/replace the wiring.

Yes

Replace the fan. If the anomaly persists, replace the P.C.B.

The wiring between the P.C.B. and fan is OK.

Check continuity of the cable on clamp 4 of connector X12.

Restore the electric connection/replace the wiring.

Yes

Replace the fan. If the anomaly persists, replace the P.C.B.

ERROR 20

Parasite flame block

The detection electrode and the relative wiring are integral.

Check and/or replace detection electrode/replace wiring.

Yes

Replace the P.C.B.

ERROR 27

Insufficient circulation

The pump functions correctly.

N.B.: make sure that the pump functions at maximum speed.

See section B

Yes

Any CH system zone valve or cut-off cocks are open.

Restore circulation in the CH system by acting on the closed devices

and also check:

- the correct functioning of the boiler by-pass;

- the opening times of any zone valves;

- the correct functioning of any thermostatic valves.

Yes

The NTC flow probe is OK (10 kΩ at 25°C).

Replace NTC flow probe.

Yes

Check/clean/replace the main heat exchanger (condensation module). If the anomaly persists, replace the P.C.B.

Содержание VICTRIX 26 2 I































































Результаты поиска

Содержание VICTRIX 26 2 I

Отзывы:

Похожие инструкции для VICTRIX 26 2 I

Бренды по названию

Популярные бренды

Immergas VICTRIX 26 2 I, Руководство пользователя

Результаты поиска

Содержание VICTRIX 26 2 I

Отзывы:

Похожие инструкции для VICTRIX 26 2 I

Бренды по названию

Популярные бренды