800-WMAGNET
14 of 21
CER05, CER07, and CER09 (plate)
MAGNET
MODELS
LOAD
THICKNESS
TYPE OF SURFACE CONDITION
CLEAN & SMOOTH
Similar to a Flat
(32 micro-inch RMS)
Ground Surface
.000” Max. Air Gap †
RUST OR SCALE
Similar to a Flat Hot
Rolled
Steel Surface
.010” Max. Air Gap †
(.254mm)
IRREGULAR OR ROUGH
Similar to a Flat Smooth
Cut File
.020” Max. Air Gap †
(.508mm)
Max. Load
(lbs.)
Max. Size
(ft.)
Max. Load
(lbs.)
Max. Size
(ft.)
Max. Load
(lbs.)
Max. Size
(ft.)
CER05
NEVER LIFT ANY LOAD WITH ANY DIMENSION GREATER THAN 5 FEET
Over 1”
600
-
400
-
370
-
* 1”
600
3 x 4
400
3 x 3
370
3 x 3
*3/4”
530
4 x 4
375
3 x 4
350
3 x 3
*1/2”
480
4 x 5
350
4 x 4
330
4 x 4
*3/8”
400
5 x 5
275
4 x 4
200
3 x 4
*1/4”
180
4 x 4
150
3 x 4
125
3 x 4
CER07
NEVER LIFT ANY LOADS WITH ANY DIMENSION GREATER THAN 6 FEET
Over 1-1/2”
1200
-
1100
-
900
-
*1-1/2”
1200
4 x 4
1100
4 x 4
900
3 x 4
*1”
1000
4 x 5
950
4 x 5
900
4 x 5
*3/4”
850
5 x 5
775
5 x 5
700
4 x 5
*1/2”
700
5 x 6
650
5 x 6
550
5 x 5
*3/8”
450
5 x 5
420
5 x 5
400
5 x 5
*1/4”
200
4 x 4
190
4 x 4
180
4 x 4
CER09
NEVER LIFT ANY LOADS WITH ANY DIMENSION GREATER THAN 8 FEET
Over 2”
2400
-
2300
-
2000
-
*2”
2400
5 x 5
2300
5 x 5
2000
4 x 5
*1-1/2”
2200
6 x 6
2100
5 x 6
1800
5 x 5
*1”
1700
6 x 6
1550
6 x 6
1400
5 x 6
3/4”
1400
6 x 7
1300
6 x 7
1250
6 x 6
*1/2”
700
5 x 6
650
5 x 6
600
5 x 5
*3/8”
525
5 x 6
480
5 x 6
450
5 x 5
*1/4”
250
4 x 5
220
4 x 5
200
4 x 4
* LIFTING CAPACITY IS AFFECTED BY PEEL AND THICKNESS. SEE NOTES 1 & 4 OF THE “IMPORTANT FACTS” (PAGE 6 & 7) IN THIS MANUAL.
† SEE NOTE 2 OF THE “IMPORTANT FACTS” (PAGE 6) IN THIS INSTRUCTION MANUAL. ALSO READ RECOMMENDED LIFTING PROCEDURES
(PAGE 10).
Values shown are for maximum rated capacities when operating instructions and warnings are followed.
Values are based upon SAE 1020 steel. Higher alloy steels and other magnetic materials will require further reductions of
these rated capacities. See Guidelines for the Reduction of Rated Lifting Capacity on previous page.
LIFTING GUIDELINES (PLATE)
