11
Exhausting cooker hood
The equipment is constructed in accordance with
European Standards and with the requirements
included in the following Directives: 2006/95EC
(Low Voltage Directive), 2004/108 (Electromagnetic
Compatibility).
1. INSTALLATION
Read the instruction manual before installing and/or
using the hood.
Range hoods and other cooking fume extractors
may adversely affect the safe operation of appliances
burning gas or other fuels (including those in other
rooms) due to the back flow of combustion gases.
These gases can potentially result in carbon monoxide
poisoning. After installation of a range hood or other
cooking fume extractor, the operation of flued gas
should be tested by a competent person to ensure that
back flow of combustion gases does not occur.
In order that the minimum distance between the
supporting surface for the cooking pots on gas hob
and low-voltage components present in the hood is at
least 65cm as required by the regulations in force, it is
necessary that the lower part of the hood is at least 65-
70cm away from the work top.
If the mounting instructions of the gas cooker indicate
a wider distance, respect it. The unit must not be
mounted above cookers fitted with top radiant plate.
Respect all the air discharge regulations.
The air must not be discharged in a pipe used to
discharge exhaust fumes produced by gas- fed
equipment or fuel-fed equipment (this does not apply to
filtering hoods).
The room must be adequately ventilated when the
hoods is used together with other gas-fed or
fuel-fed equipment.
The hood is equipped with all the necessary fastenings
for its installation, which are suitable for most surfaces.
Anyway, ask to a professional to verify that the
installation surface is strong enough. Installation must
be carried out by qualified installers according to
present regulations.
For an easy access, it is advisable to move possible
furniture under the installation area. For mounting the
hood follow the illustrations in Fig. 1.
Install in the cabinet the two metal brackets provided
with the cooker hood (Fig. 2) at a distance of 40 mm
from the front edge and not less than 37 mm from the
bottom edge of the cabinet itself.
Install the hood inside the cabinet (Fig. 1) and fasten it
with four screws to the brackets, then close the holes
with the caps provided (Fig. 3).
2. ELECTRICAL CONNECTIONS
This appliance must be connected to an earthed power
supply. Two types of electrical connection can be used:
1. Using a standard plug to be connected to the power
cable and inserted in a mains socket which must be
accessible (so that the plug can be disconnected when
servicing is carried out). Make sure that the plug is
accessible also after the complete installation of the
equipment.
2. By means of a fixed mains connection, fitting a
bipolar switch, which ensures the disconnection, with an
opening distance of the contacts allowing a complete
disconnection on the conditions of the over voltage
III category, according to installation regulations. The
ground connection (yellow-green wire) must not be
interrupted. For stationary appliances permanently
connected to the fixed wiring, compliance with this
requirement is considered to be met if the instruction
concerning disconnection incorporated in the fixed wiring
is in accordance with AS/NZS 3000
Refer to the plate inside the hood for the mains voltage
and frequency ratings.
3. USE
This cooker hood can be employed as exhausting or
filtering. Exhausting. The carbon filters should not be
installed on the hood in exhausting version.
Kitchen smokes are driven outside through a flue joined
to the exhaust pipe flue connector.
Pipes must be communicating with the exterior of the
house. This pipe must not under any circumstances be
connected to cooker, boiler or burner exhaust pipes, etc.
Filtering. The fumes pass through the carbon filters
to be purified and recycled into the kitchen through a
pipe connected to the outlet of the hood up to the hole
in the top of the cabinet. This hole must be free and
communicating with the kitchen.
In the filtering version you must install the carbon filters.
To carry out this operation, you must first remove the
metal grease filters, mount the frame with the screws
provided and then snap the charcoal filters in the same.
(fig.5).
INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS FOR
RANGE HOODS DESIGNED FOR WALL FITTING 230 Vac • 50 Hz
