background image

If your Slides become Jammed 

Bent or damaged slides may become jammed in the projection position. 

Make sure the projector is disconnected from the mains supply, and 

then remove the two retaining screws underneath the projector (9). 

The top casting can now be lifted off, and the slide released by 

hand. 

Before you reassemble the projector, make sure the capping blade is 

operating correctly. 

If you are going to carry your Sportsview Projector when it is loaded 

with a magazine containing slides, it must always be held in the normal 
operating position. If it is carried on its side, or if it is shaken or 
bumped about, the slides will come out of the magazine and jam the 
mechanism. 

Screens 

A square screen with a matt white surface is the most suitable type 
for use with the Sportsview Projector. By using a square screen, you 
can show either vertical or horizontal slides without moving the 
projector, and the matt white finish gives maximum brilliance for all-
round home use. 

The following table gives the picture sizes you will obtain at various 

projection distances. This will help you to select the most suitable 
screen size for your purposes. 

Approximate Picture Size 

Projection from Recommended 

Distance 24 x 36 mm. Screen Size 

Transparency 

Feet Inches Inches 

5 18x27 30x30 

8 24 x 36 40 x 40 

10 32x48 50x50 

Содержание Sportsview













Отзывы: