Ikra LS 3011, Руководство по эксплуатации

Страница: 20 / 44

Unpacking
Due to modern mass production techniques, it is unlikely
that your power tool is faulty or that a part is missing. If
you find anything wrong, do not operate the tool until the
parts have been replaced or the fault has been rectified.
Failure to do so could result in serious personal injury.
Preparing of the blower vac prior to use
The blower vacuum requires some assembly prior to use
for the first time This includes the fitting of the blow/vac
tube to the housing and the fitting of the collection bag.
Assembly
Before putting the device into operation, the
blower / suction tube must be completely
mounted and screwed tight and the collection
bag and carrying strap must be attached.
Mounting of blower / suction tube
Make sure the tubes are held straight during
mounting. The electrical contacts in the tube
could be damaged.
1. Connect the two separated tubes, and make sure the
two parts of the tube engage, where upon they can-
not be disengaged for safety reasons. (See Fig. 1)
2. Loosen the 4 screws on each side of the end of
blower / suction tube. (See Fig. 2)
3. Insert the blower / suction tube into the blower / suc-
tion opening on the motor house totally. And fasten it
with 4 screws. (See Fig. 3+4)
NOTE:
There is a interconnection cord within the
suction tube, if the blower / suction tube was not well
assembled, the machine can not start.
Telescopic extension (See Fig. 5)
This device offers the possibility to adjust the length of
the suction/blowing pipe to adapt it to the height of the
operator. To do so proceed as follows:
Push the locking button 13 (Fig. 6). The pipe extension
is now unlocked. Now pull the lower end of the pipe (3
steps adjustment) and lock the pipe again with locking
button 13.
Mount grass collection bag (See Fig. 6+7)
1. Place the grass collection bag retainer frame onto
the opening on the outlet of the motor house. So that
the grip points towards the mains cable. Press the
retainer frame over the engagement strip until the
coupling lever engages. Suction operation is only
permissible with the grass collection bag mounted.
2. Connect the grass collection bag retainer loop to the
blower / suction tube.
Mount carrying strap
(See Fig. 8)
Hook the carrying strap onto the bracket on the motor
housing.
Operation
WARNING !
1. Wear suitable clothing and work gloves when wor-
king with the device.
2. Make sure that the grass collection bag and the blo-
wer / suction tube are assembled correctly and the
shoulder strap is adjusted correctly for work.
3. Make sure that the device is functioning properly
before every use.
4. Make sure the all control in good condition. Do not
use the machine if the control disable.
5. Make sure that the mains voltage values are compa-
tible with the label on the device.
6. Note noise protection laws and local regulations.
The use of the device can be restricted or rohibited
on certain days (e.g. Sundays and holidays), during
certain times of the day (lunch hours, at night) or in
special areas (e.g. health resorts, clinics etc.).
7. After switching off the device, the impeller wheel
continues to rotate for some time.
Switching on and off, operating mode change
Before switching on device, make sure it is
not in contact with any objects. Ensure stable
positioning
1. Make a loop of the end of the extension cord and
fasten this to the cable support. By means of this ten-
sion relief, an unintentional pull-out of the electrical
plug connection is avoided. (See Fig. 9)
2. Make sure that the device is switched off and con-
nect the device to the main voltage.
3. Keep proper footing and stance during work. Place
on the shoulder strap and hold the device with one
hand on the casing handle and with the other one on
the front grip. Ensure the device is not in contact with
any objects before the switch-on.
4. In order to selection of the operating mode, rotate
the blower/vacuum selector lever (4) as shown in the
required symbol. (See Fig. 10)
Blowing operating mode
Suction operating mode
WARNING! Before changing the operating
mode, it is absolutely necessary that the de-
vice be switched off.
5. For switch on, slide the on/off switch into position “l”,
the device starts up. (See Fig. 11)
6. To switch off, slide the on/off switch into position “0”,
the device stops.
7. The speed control need be set the optimal blowing
and sucking strength. (See Fig. 12)
Working with the garden leaf blower blowing ope-
rating mode
1. Set the operating mode selector lever to the symbol
(See Fig. 13)
2. You will get optimal results when you use the blower
with a separation distance to the ground of 5 -10 cm.
GB-5