9
Switching on the device
Check whether the voltage given on the type plate corresponds to
the available mains voltage.
The socket used must be earthed (fitted
with earth contact).
If these conditions have been met, the machine is ready for opera-
tion when the mains plug is plugged in.
If these conditions are not met, safe operation is not guaranteed
and the machine could be damaged.
Before the first time to use the stirrer, fasten the
WiCo
to the sta-
tion with the screw (P, see Fig. 1), so that the rechargeable battery
(RB1 battery pack) in the
WiCo
can be charged.
After the device has been switched on at the mains switch (A, see
Fig. 1) the device name and software version appear in the display
(C, see Fig. 1) of the
WiCo
(D, see Fig. 1). After a few seconds a
signal sounds, the last setting of speed is displayed (mode B). Once
the working screen is displayed, the stirrer is ready for operation.
If the
WiCo
is switched on and is not attached to the stirrer (the sta-
tion), the green LED bar (G, see Fig. 1) and the green Bluetooth
®
LED
(F, see Fig. 1) on the stirrer (station) will light up. Make sure that the
speed selected is appropriate for the trial run. If in doubt, use the
rotary knob (B, see Fig. 1) to select the slowest speed. To start or stop
the stirrer function, press the rotary knob (B).
The control elements of the
WiCo
can be disabled by pressing
the button (L, see Fig. 1) about 2 seconds, so that no inadvertent
changes are made while the device is running (the lock symbol
appears in the display).
Presse the button (L) about 2 seconds enables the control ele-
ments again (lock cymbol
disappears from the display).
In emergency the stirrer (station) can be
switched off by pressing the “
safe STOP
“
button (I, see Fig.1) on the front of the stirrer. In this case the LED
bar (G, see Fig.1) changes color from green to red, and flashes.
A message appears on the display, advising that the stirrer (station)
has been forcibly switched off. To restart the stirrer, switch the main
sswitch (A, see Fig. 1) of the stirrer (station) OFF and ON.
If the Bluetooth
®
function of the
WiCo
is active, you can use the
Bluetooth
®
search button (H, see Fig. 1) to search for the
WiCo
. A
beep signal will be audible even if the
WiCo
is switched off.
• Speed setting:
You can use the rotary knob (B, see Fig. 1) to pre-set the required
speed before you start the device. If you then press the rotary
knob(B) the device starts at the speed you set. When a change
is made to the speed, the rated speed is shown in the display (C,
see Fig. 1). When the device is stopped, the button (K, see Fig.
1) can be used to switch between the two speed ranges (
I
and
II
). When in standby mode, the display (C) shows the set speed.
The stirrer has two different speed ranges:
Range I:
low speed, high torque.
Range II:
high speed, low torque.
• Correct procedure for changing the speed range:
- Switch the device off at the rotary knob (B, see Fig. 1).
- Switch the speed range with button (K, see Fig. 1).
- Change the speed with the rotary knob (B).
- Switch the device on at the rotary knob (B).
- The speed can be varied at any time in operation.
- The speed appears in the display (C, see Fig. 1).
NOTICE
Useful information
The stirrer is controlled via a
WiCo
. If the
WiCo
is attached to the
station
, data exchange between the stirrer (station) and
WiCo
is performed via the contacts (E, Q, see Fig. 1). "Home" symbol
appears on the display of the
WiCo
. If the
WiCo
is connected
to the stirrer (station) via a USB (Universal Serial Bus) cable, the
symbol appears. If the
WiCo
is neither bolted to the
station
nor connected to the stirrer (station) via a USB cable, the data
exchange between the stirrer and
WiCo
is performed via Blue-
tooth
®
. In this case the Bluetooth
®
symbol is displayed.
Depending on the structure of the building, the
WiCo
can be op-
erated at a distance of up to 150 m from the
station
, using the
Bluetooth
®
connection.
The
WiCo
can be attached to the stirrer (station), or can be in-
stalled in a safe place easily accessible by you while the stirrer is
running.
If the
WiCo
is attached to the
station
, the rechargeable battery
is automatically recharged via the contacts (Q, see Fig. 1). The re-
chargeable battery can also be charged via the USB port of the
WiCo (see “Charging the RB 1 battery pack (rechargeable battery)“
in the “Securing“ section).
If the stirrer (station) generates vibration, the
WiCo
must be bolted to the stirrer using the
screw (P, see Fig. 1), or positioned remotely from the stirrer (sta-
tion) whilst it is running.
NOTICE
