IHP Superior Fireplaces F3412 Скачать руководство пользователя страница 20

Страница: 20 / 32

SuperiorFireplaces.us.com

900855-00_C

Door rail

Top Face

Screw

Spring

Clip

GLASS DOOR INSTALLATION

Figure 41 - Installing Bi-Fold Doors

Figure 40 - Installing Door Rail

Spring Clip

Insert Pin into

Spring Clip

Pivot

Hole

Insert

Bottom Pivot

Pin into Hole

Fold Door and

Slide Top Pins

Into Track

Figure 42 - Adjusting Bi-Fold Doors

INSTALLING OPTIONAL GLASS DOOR MODELS 38LBF and 43LBF

Use only the doors that are listed for use with these fireplaces. Use

of other non-listed glass door on these fireplaces may constitute a

potential fire hazard and is not recommended.

Note:

Top door rail, and spring clips are provided with the glass

door kit.
1. Using a Phillips screwdriver, remove the three (3) factory

installed screws underneath top front face.

2. Position the door rail and secure it with one (1) of the screws

removed, start from the middle as shown in Figure 40.

3. Using remaining two (2) screws, secure both the spring clips

and the rail for the left and right sides as shown in Figure 40.

WARNING

This kit is to be installed by a qualified service

technician or other qualified agency in accordance

with the manufacturer's instructions and all codes

and requirements of the Authority Having Jurisdiction

in the USA or Canada. If these instructions are not

followed exactly, a fire or explosion may result,

causing property damage, personal injury, or loss

of life. The qualified agency performing this work

assumes responsibility for this installation.

4. With bi-fold doors completely folded, insert bottom pivot pin

into pivot hole located near bottom corner of front face opening

and swing door to vertical position making sure top pins slide

into door track. Door is installed when top door pin snaps into

spring clip (see Figure 41).

5. Repeat step 4 for remaining door.
If you find doors do not close properly or do not appear level or

straight, proceed with section on door adjustment.

DOOR ADJUSTMENT

Remove doors and slightly loosen upper spring clips. Replace

doors and fully close them. Use 1/8" shims (any material) to

level doors. Once proper setting is achieved, carefully open

doors enough so that you can access spring clips with a Phillips

screwdriver. Tighten screws. See Figure 42.

Содержание Superior Fireplaces F3412

































Результаты поиска

Содержание Superior Fireplaces F3412

Отзывы:

Похожие инструкции для Superior Fireplaces F3412

Бренды по названию

Популярные бренды

IHP Superior Fireplaces F3412, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Superior Fireplaces F3412

Отзывы:

Похожие инструкции для Superior Fireplaces F3412

Бренды по названию

Популярные бренды